E-bike chassis dynamometer testing machine
Electric bicycles are complex systems involving mechanical, electrical, and control components. Evaluating their performance and compliance with safety and efficiency standards requires precise and repeatable testing that is difficult to achieve in outdoor environments due to varying weather, traffic, and road conditions. An Electric Bicycle Chassis Dynamometer System addresses this need by providing a consistent platform for comprehensive e-bike testing.
Standard
EN 15194:Cycles - Electrically power assisted cycles - EPAC Bicycles
ISO 4210:Cycles - Safety requirements for bicycles
UL 2849:Standard for Electrical Systems for eBikes
Application
Measuring motor efficiency, power output, and torque characteristics of e-bikes.
Evaluating battery range and energy consumption under simulated riding conditions.
Simulating various road loads, inclines, and driving cycles.
Testing electromagnetic compatibility (EMC) by providing a stable environment.
Conducting endurance and durability testing on e-bike components.
Verifying compliance with national and international standards for e-bike performance and safety.
Research and development of new e-bike designs, motors, batteries, and control strategies.
Quality control and validation during the e-bike manufacturing process.
Product Advantages
Provides a highly controlled and repeatable testing environment, eliminating variables from outdoor riding.
Enables precise and accurate measurement of critical e-bike performance parameters.
Allows for rapid and efficient testing for product development and quality control.
Enhances safety by performing tests in a controlled indoor setting rather than on roads.
Supports compliance testing against various national and international e-bike standards.
Facilitates detailed data acquisition and analysis for in-depth performance evaluation.
Offers versatility to simulate a wide range of riding conditions and custom test cycles.
Accommodates various e-bike types and sizes through adjustable mounting systems.
Parameters
| Item | Detail |
|---|---|
| Loading Method | Inertia |
| Maximum Power | 200 kW (300 HP) |
| Max Speed | 350 km/h |
| Roll Inertia | 8.16 m²·kg |
| Roll Diameter | 450 mm |
| Roll Width | 235 mm |
| Max Impasto | 1.57 m |
| Vehicle Size | e - bike |
Accessoriess
Roller
Power absorption device
Inertia simulation device
Drive motor
Speed sensor, etc.
Test Procedures
Preparation: Ensure the dynamometer is in good working order and prepare the necessary tools and equipment for the test. Check that the electric vehicle under test meets the test requirements, such as being fully charged and free of malfunctions.
Connect the power supply: Connect the electric vehicle to the dynamometer and switch on the power. At this point, the dynamometer should be in a "no-load" state.
Set parameters: Set the appropriate parameters according to the test requirements, such as test time and speed range.
Start the test: After confirming that all parameters are set correctly, start the test program. The dynamometer will perform the test according to the set parameters and record the test data.
End the test: After the test is completed, close the test program, disconnect the power supply, and remove the electric vehicle. The test results can then be viewed and data analysis can be performed.
Send product request
Other supplier products
 |
Coating thickness gauge/film thickness gauge | Standard Coating Thickness Gauge complies with international standards includingASTM B499,ASTM D1400,ISO 2178,ISO 2360, andGB/T 4956, ensuring rel... |
 |
Scrub Abrasion Tester | T107 Scrubbing Tester, It is suitable for various abrasion and wet scrubbing tests, which is commonly used in scrubbing resistance tests for interi... |
 |
Office Chair Caster Durability Tester | The Office Chair Caster Durability Tester is designed to evaluate the rolling durability, structural reliability, and service life of office chair ... |
 |
Carbon Arc Aging Chamber | Carbon arc aging chamber is mainly used to simulate the destructive effects of ultraviolet rays, temperature, humidity and other factors in natural... |
 |
Artificial turf wear tester | An artificial turf wear tester is a device specifically designed to evaluate the wear resistance of artificial turf. It tests the wear performance ... |
Same products
 |
Full-Body Garment Stress Tester,FZ/T 70015 | Seller: Standard International Group (HK) Limited | TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe... |
 |
Industrial Dry Cleaning Machine,industrial garment steamer | Seller: Standard International Group (HK) Limited | TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel... |
 |
MST Medical Compression Stocking Tester,compression sock tester | Seller: Standard International Group (HK) Limited | The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the... |
 |
MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool | Seller: Standard International Group (HK) Limited | Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi... |
 |
Dental material color stability tester | Seller: Standard International Group (HK) Limited | Application The applications of color stability testers for dental materials are mainly reflecte... |
