Filter Media Tester GVT 3000
Upgrade of existing filter test channels for room air filters with aerosol technological components in accordance with EN779, ASHRAE 52.2 and ISO FDIS 16890 incl. automation
For over 3 decades, Palas®has built filter test systems for filters and filter media or has upgraded existing test rigs with components, such as aerosol generators (droplets, salts and solids), aerosol spectrometers, dilution systems, discharger systems and automation software.
In the field of room air filtration, more than 14 existing test rigs have already been upgraded and automated using Palas®technology to the complete satisfaction of our international customers.
Upgrading and automation of particle measurement, as offered by Palas®with the GVT 3000 (GeneralVentilationTest System Upgrade), serves in quality assurance and the development of filters in EN779, ASHRAE 52.2 and ISO FDIS 16980 test rigs. The upgrade consists of an aerosol spectrometer, incl. laptop/PC and monitor, aerosol generators (optionally: discharge unit), sampling system, as well as automation of the measurement process.
The Palas®aerosol generators offer unrivalled consistency in terms of the particle concentration and size. This forms the basis for the very good repeatability of test results using the Palas®filter testing systems and test rig upgrades.
Thanks to the high-resolution light scattering spectrometer Promo®3000, the fraction separation efficiencies can be determined with greater ease, speed, reliability and accuracy. With the aid of patented optical fibre technology, there are practically no particle losses in the sampling lines, as the sensors can be positioned directly at the measurement point.
With the Fidas®system, Palas®offers the only optical aerosol spectrometer certified in accordance with EN 12341:1998 and EN 14907:2005 for PM2.5and PM10measurements. The Palas®aerosol spectrometer Promo® is almost the same in the design as the certified Fidas®system and provide reliable PM values for filter testing. FTControl from Palas®is simple, reliable and fast filter testing software that has been proven internationally. It enables the test procedure to be executed fully automatically in accordance with EN 779, ASHRAE 52.2 and ISO FDIS 16890, including generation of standard-compliant test reports.
Our quality in detail
The GVT 3000 test rig upgrade is modular and can therefore be adapted to the relevant standards.
• Filter testing in accordance with EN 779:2012
• Filter testing in accordance with ASHRAE 52.2
• Filter testing in accordance with ISO FDIS 16890
Individual components of the GVT 3000 test rig upgrade:
1.Variable aerosol generation:Depending on the standard for testing, Palas®offers aerosol generators for dispersion of different dusts (e.g. A 1 - A4, ASHRAE, Aramco etc.), salts (e.g. KCl/NaCl), oils (e.g. DEHS) and suspensions. All generators are clearly characterized according to the new VDI 3491 and offer the highest dosing consistency in terms of particle size distribution and particle concentration. Shortening of the measurement time, e.g. through increased dust concentration.
2.Discharge: (ISO FDIS 16890):ISO FDIS 16890 calls for aerosol discharge using KCl as the test aerosol. Palas® offers an electrical system, CD 2000, for this purpose. Special advantage: The discharge is easy to switch on and off and is almost maintenance-free.
Other supplier products
|
|
ASTM D3939 ICI Mace Snag Tester for snagging performance test |
The ICI Mace Snag Tester is equipped with an observation box and the comparison pattern card with different fabric structure. It is equipped with f... |
|
|
taber linear abraser |
The Taber Linear Abraser incorporates a horizontal arm that reciprocates in a linear motion. Attached to the end of the arm is a precision bearing ... |
|
|
Geotextile Plane Flow Meter |
Introduction:In order to evaluate the water conveyance capacity of the material, the geotextile surface flow meter was used to measure the permeabl... |
|
|
Finished Shoes Bending Strength Tester |
Finished Shoes Bending Strength Tester is used to determine bending resistance of finished shoes and soles to improve quality. Bend shoes and soles... |
|
|
Thermal Contact Tester |
The instrument is designed for the assessment of materials and material combinations that are exposed to a heat radiation source.In procedure A exp... |
All supplier products
Same products
