45 Degree Automatic Flammability Tester

• 

45 Degree Automatic Flammability Testertest instrument is used to detect the flame resistance of the blanket fabric and the flame spread performance of the fabric surface.including bed sheets, blankets, mattresses, pillows, duck down quilts and plush fabric products used to cover the bed.

Test principle:

Within a specified time, the surface of the test sample is burned with a standardized flame, so that the burning, damage degree or discoloration of the standard test paper can be observed, and then the test fabric can be graded and evaluated.

Body stainless steel structure:
SCM control, control interface friendly, easy to operate
Heavy hammer timing stop device, timing accurate
Standard fire mouth
Accessories and Consumables:
Combustion gas supply Device
50 mercerized cotton sewing machine line

Features:

Stainless steel case with transparent viewing window

18 Needle flame, flame length adjustable

Ignition time can be set freely

Automatic timing of flame spread in 0.1 second increments.

Automatic or manual flame impingement for 1,5 or 20 seconds.

Provide bristles and sample clamps

Provide standard stainless steel sample holder

Technical Parameters:

▶ Flowmeter : Adjust the gas flow size;
▶Fire tube : The gas is first connected to the flow meter through the hose, and then through the rear hose of the box into the flame pipe;
▶Windscreen: the upper part of the windshield is provided with glass;
The experiment was carried out in a ventilated kitchen. The round hole on the top of the box and the gap on the windshield make the gas convection.
▶Control panel : Power- power switch ;Start:Start internal motor operation. When the flame tube moves to the test position (the vertical distance from the sample center is 8mm, the horizontal distance is 3.2mm), the internal timing switch is touched;
▶Reset : Timer reset /Fire tube reset;
▶Sample clamp and specimen holder : The sample frame substrate is provided with a knob which can adjust the left and right movement, and the sample frame substrate is moved and fixed by loosening and tightening the knob;
▶Timer :Display settings and actual ignition time.After the time is cleared, the fire tube can complete the required movement. Or the fire tube can not return to the original position after moving forward;
▶Test room size: W368 × D216 × H356mm
▶Sample shelf angle: 45 °
▶Flame spread time setting range: 0.01S-99.99S
▶ignition time of the sample surface : 1.0S ± 0.05S

Other supplier products

	Wet Microbial Penetration meter	The wet microbial penetration tester is mainly used to evaluate the barrier ability of medical protective equipment (such as surgical gowns, isolat...
	Fogging Tester	Standards DIN 75201: Automotive trim material fogging resistance. ISO 6452: Coated fabrics fogging behavior in vehicle interiors. SAE J1756: A...
	Metal Bone Screws Torque Tester	Standard YY/T 1506. ASTM F543: The standard specifies the torque required to measure the torque required to screw a metallic bone grafting screw ...
	Solid Combustion Rate Tester	Product Introduction This product complies with "Recommendations on the Transport of Dangerous Goods - Manual of Tests and Criteria" 33.2.1.4 Test...
	Automotive seat frame durability tester	Applicable standards: GB 11550-2009 "Performance requirements and test methods for car seat headrest" : Appendix B of this standard specifies the ...

Same products

	Steaming Cylinder	Seller: Standard International Group (HK) Limited	Standards ISO 3005. BS 4323. NEXT TM 15. M&S P8. IWTO 29-76 Applications: Used for steamin...
	Drill Flocking Performance Tester丨Drill Flocking Performance Test mechine	Seller: Standard International Group (HK) Limited	Standards GB/T 12705.1/14272. BS EN 12132-1 Applications To determine the ability of penetrati...
	Wrinkle Recovery Tester 丨Wrinkle Recovery Test mechine	Seller: Standard International Group (HK) Limited	Standards AATCC 128, ISO 9867, ENKA 3061 Applications AATCC Wrinkle Recovery Tester is used to...
	Button Impact Tester丨Button Impact Test mechine	Seller: Standard International Group (HK) Limited	Standards ASTM D5171 Applications Button Impact Tester is used to determine the impact resista...
	AATCC Viewing Board丨AATCC Viewing Board tester	Seller: Standard International Group (HK) Limited	Standards Built to American Association of Textile Chemists and Colorist (AATCC) approved test m...