Shoelace anti-siphon tester
Product Introduction:
Shoelace anti-siphon tester is suitable for all kinds of waterproof leather, leather, mesh, waterproof shoelace, ribbon waterproof performance.
Anti-siphon:
The force phenomenon of the difference in liquid level height is used to draw water from low places to high places. The anti-siphon effect on textiles is similar to the capillary effect. After the fabric touches the water, the water will spread through the fabric and spread to the high places of the fabric.
Waterproof:
Refers to the waterproof agent on the surface of the fabric to form a film, so that water can not penetrate the inside of the fabric is called waterproof.
Anti-siphon can be divided into static anti-siphon and dynamic anti-siphon two categories. Static anti-siphoning is to adopt a static suspension method to observe whether the liquid immersed in the fabric has a climbing phenomenon, and the climbing height to assess whether it is qualified.
Product Advantages:
Measures Key Moisture Management Property: Quantifies static wicking or anti-siphon behavior, which is important for footwear comfort and preventing water ingress.
Suitable for Various Materials: Applicable to a range of footwear components and materials, including textiles, leather, and laces.
Simultaneous Testing: Allows testing of multiple samples concurrently (up to 20), increasing efficiency.
Provides Objective Measurement: Measures the actual height of water climb over a specified time.
Simple Test Principle: The static suspension method is straightforward to implement and understand.
Product Features:
Stand or rack with multiple stations for vertically suspending test specimens.
Water bath or trough at the base with controlled water level (450mm maximum height capability, although the immersion position is 13mm).
Clips or clamps to hold the upper end of the samples securely on the suspension stand.
Measuring scale or ruler positioned alongside each sample to accurately read the height of water rise.
Capability to test a specific number of samples simultaneously (20 samples).
Designed to accommodate specific sample sizes based on material type (Leather, mesh: 7625MM; Shoelaces, webbing: 76width MM; Line type: 76*width MM).
Designed for testing with a specific immersion position (13mm) and suspension times (0.5 hours and 2 hours).
Sampling requirements:
1. Leather, mesh: 76*25MM
2. Shoelaces, webbing: 76* width MM
3. Line type: 76* width MM
4. Samples can be tested at the same time: 20
5. Water level height: 450mm
Test requirements:
1. Immersion position: 13MM(0.5 inches)
2. Suspension time: 0.5 hours and 2 hours
Send product request
Other supplier products
 |
Pipes Hydrostatic Testing Machine/ Pipeline Pressure Resistance Tester / Pipe Burst Pressure Tester | Standard ISO 1167: For thermoplastics pipe systems under constant internal pressure. ASTM D 1598: Standard test method for time-to-failure of p... |
 |
Skein Length Tester | Standards: GB/T 4743 Textiles－Yarn from packages－Determination of linear density (mass per unit length) by the skein method GB/T 14343 Testing m... |
 |
Shoe Peeling Strength Tester | Main uses: The shoe stripping tester is mainly used to measure the bonding strength between the upper and the sole or other shoe components. By si... |
 |
Digital Grinding Machine | Standard: GB/T 5211-16.GB/T 5211-19.GB/T 21867.1.GB/T 21868.5.ISO 787-16.ISO 787-17.ISO 8780-5.ISO 8780-1 I. Definition and Working Principle Di... |
 |
Spinal Internal Fixation System Component Testing Machine | Standard YY/T 0119-2014 (China): Specifies mechanical testing protocols for spinal fixation components, including screws, plates, rods, and conn... |
Same products
 |
Scott Flex Tester | Seller: Standard International Group (HK) Limited | Product Introduction: Scott kneading tester is suitable for back and forth kneading resistance o... |
 |
NEU nanofiber electrospinning device | Seller: Standard International Group (HK) Limited | Content The Nanofiber Electrospinning Unit uses electrospinning techniques to safely and easil... |
 |
KK03 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK02 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
 |
KK01 Scratch tester | Seller: Standard International Group (HK) Limited | Product Introduction: With the continuous expansion of the use of plastic molding products, from... |
