20V Vane Pumps with Lower Noise

V Seriesvane pumps with lower noise are intra vane pumps, featured by advanced performance, high pressure, stable operation, lower noise, ultra-low pulse, long life-span and so on, and are widely used in cutting, plastic, leather, pressure , engineering, metallurgical machinery fields, and the like.

Installation and Use
1. In installation, the tolerance of concentricity between shaft of pump and motor must be less than 0.10mm (TIR) ​​and the maximum permissible angle error is less than 0.2 degrees by using the flexible coupling; The pump shaft shall not bear the radial and axial load ; The carrier must be firm with good rigidity and can fully absorb vibrations.

2. Fix pipes, especially inlet pipes in accordance with the size of port and assemble safety relief valves in the system (the inlet flow rate is between 0.5 and 1.5 m / s). The regulating pressure of the safety valve shall not be greater than the maximum pressure of the pump; Inlet pipes must be strictly sealed with no leakage; Inlet pipes must be strictly sealed with no leakage; The fuel tank shall be equipped with a diaphragm to separate the bubbles and dirt from the oil; The oil return nozzle should be lower the fluid surface, the minimum depth of 50 mm, even in a low, too, when the permissible level of to avoid the formation of bubbles.

3. Set the suction pressure at pump inlet port: oil hydraulic oil is + 35 ~ -16.7 KPa. The hydraulic oil of water-glycol and phosphate ester was + 35 ~ -10.1 KPa.

4. In case where the pump is installed on the tank or at the position higher than the tank top cover, the height of the suction port of the pump should be less than 500mm.

5. Oil should be kept clean, pipes and tanks must be thoroughly cleaned; Precise filters should be assembled with the advised precision of 25μm in the system, the cleanness level of oil should be within NSA12. Fix the sufficient-volume filter (the rated flow rate should be greater than twice the pump flow) at the inlet of the pump 50mm above the bottom of the tank, with the suggested precision of 100μm (150 mesh).

6. It is recommended to use antiwear industrial hydraulic oils or automotive crankcase oils having letter designations SC, SD, SE or SF with viscosity grades of 32 to 68 cSt at 40 ℃

Preferred viscosity at rated speed and pressures:

Min. 13cSt Max. 54cSt

Min. 49 ℃ Max. 65 ℃

7. Check the inlet, outlet and direction of rotation before starting the pump. Turn the shaft of pump evenly and nimbly by hand after fixing the pump. It is best to fill the pump with oil for the first time.

At an initial operation or at an operation after a long rest, the pump may have difficulty in sucking up fluid; In such cases, an air bleed valve should be installed beforehand on the discharge side or discharge air by slightly slackening the connection on the discharge side. At starting, operate the pump intermittently as far as possible with no load.

8. Do not start the pump when the outlet pressure is lower than the inlet pressure. This will cause work noise and blade instability.

9. At startup, If the oil viscosity is higher than the suitable viscosity (54cSt), the pressure should be limited to 50% or less of their respective rated values ​​until the system has warmed up.

Zhejiang Yongling Hydraulic Machine Co , Ltd. specializes in the production and supply of high-quality vane pumps and Vane Pumps Cartridge Kits products in China. Follow us to learn more product information and technical information：

Other supplier products

	20V Vane Pumps with Lower Noise	V Seriesvane pumps with lower noise are intra vane pumps, featured by advanced performance, high pressure, stable operation, lower noise, ultra-low...
	T6C / T6CL针式叶片泵高压	该产品使用浮动侧面板，销钉结构的叶片，双刃叶片技术和全新的低噪音技术固化来加工定子。与其他定量叶片泵相比，其优点是： ●高工作压力–可以减小液压执行器，控制阀和油管的尺寸，从而降低成本，还可以通过降低工作压力来延长其使用寿命。 ●高效–体积和机械效率均高于94％，因...

供应产品

Same products

	Floral Garden Tools Set	卖方: Dongyang Guorui Industry And Trade Co., Ltd.	Investing in a floral garden tools set not only enhances your gardening experience but also add...
	Rice Husk Pellet Machine	卖方: Jiangsu Kingwood Industrial Co., Ltd.	● JWZL-420 is the most popular biomass/woodpellet machine of all the pellet mills offered by Ch...
	希腊-小型气相液氮储存罐-液氮容器	卖方: 河南天之道生物科技有限公司	在科技不断进步的今天，随着现代科研和医疗领域对生物样本的低温保存要求越来越高，小型气相液氮罐的出现，成为这一领域的理想选择。下面KGSQ厂家为您具体介绍一下它的优势特点。 1.气相/液相储存 小...
	Common Rail FuCommon Rail Fuel Injector Nozzle L500PBCel Injector Nozzle L500PBC	卖方: 738347	Common Rail Fuel Injector Nozzle L500PBC 0 445 110 189 Injector Valve Set 0 445 110 190 Injector...
	Common Rail FueCommon Rail Fuel Injector Nozzle F00VX40014l Injector Nozzle F00VX40014	卖方: 738347	Common Rail Fuel Injector Nozzle F00VX40014 Common Rail Fuel Injector Nozzle F340 Common Rail ...