FUXI ® FLUOROCARBON PAINT
Under FUXI® brand, Jinhai Special industrial painthas developed our own formulation system, including epoxy, phenolic, alkyd, acrylic, silicone, polyurethane, fluorocarbon, chlorinated rubber, ethylene and other coatings. We keep developing new solvent-free paints, water-based paints and eco-friendly coatings, interior wall paint, polyurethane paint, Solvent-Free Coating, marine grade paint and earnestly fulfil the social responsibility of environmental protection.
The high molecular polymer formed by the polymerization of fluoro olefin or the copolymerization of fluoro olefin and other monomers is fluorocarbon resin. The paint with fluorocarbon resin as the film-forming is fluorocarbon coatingor call PTFE paint. It is with outstanding weather resistance and highly decorative performance, most offluorocarbon coating are used as a topcoat or finish paint for bridge, highway guardrail, high-grade building, petroleum equipment and storage tank.
Precautions for Fluorocarbon PaintConstruction
- 2. When storing fluorocarbon paint, it is best to store it in a dry and non-sun place to avoid moisture or direct sunlight that will affect the product's service life and effect.3. During construction, paintevenly, avoid sagging or omission, which will affect the appearance.4. When preparing the slurry, the amount should not be too much each time, and the prepared slurry should be used up within 5 hours to avoid invalidation after the activation period.5. When preparing the slurry, a professionaldiluentmust be used for dilution.6. Pay attention to the construction environment, and do not work in rainy, snowyor frosty weather. In addition, it cannot be constructed in an environment with a humidity greater than 80%.7. After the construction is completed, it is necessary to wait 7 days to complete the curing, and it cannot be put into use before this.8. During construction, wear protective equipment, such as eye masks, to prevent the slurry from hurting the eyes. If you accidentally get the slurry, rinse it with clean water and seek medical attention in time.
Fluorocarbon Coating vs Powder Coating
About performance: The performance of fluorocarbon coatings is better than powder coatings, wearproof, weather fastness , UV resistance and resistant to fading. Fluorocarbon spraying is used outdoors, while powder coatings are used indoors.The price of fluorocarbon spraying is about 10,000 per ton higher than powder spraying.About spraying technology: Both powder spraying and fluorocarbon spraying are suitable for assembly line spraying. They bothrequire surface treatment before spraying.But the specific technology has some difference. Fluorocarbon coatingcan be electrostatic spraying or conventional spraying.While electrostatic spraying, friction gun spraying, fluidizedbed spraying and other methods can be used for powder coatings.
Fluorocarbon Coating Process
The pre-treatment before spraying is to remove oil stains and chemical treatment on the surface of the workpiece before spraying the aluminum alloy profile, thereby prolonging the service life of the paint film.
在线联系供应商
Other supplier products
 |
Epoxy Zinc-rich Shop Primer | High Build Zinc-rich Primer Epoxy high zinc primer is a two-component self-drying paint, composed of epoxy resin, special resin, zinc dust, additiv... |
 |
FUXI ® ASPHALT ANTICORROSIVE PAINT | Can IPaint Asphalt Coal tar pitch is obtained by fractional distillation of coal tar. It has better water resistance and chemical resistance. It... |
 |
Internal Drag Reducing Epoxy Anticorrosive Coating | Fuxi® Internal Coatingreducing epoxy anticorrosive coating is a two-component epoxy coating, which is specially developed for the inner wall of... |
 |
Chlorinated Rubber Anticorrosive Primer (Iron Red) | Chlorinated Rubber Anticorrosive Primer (Iron Red) Chlorinated rubber anticorrosive primer is combined with a chlorinated rubber resin, curing age... |
 |
Epoxy Intermediate Floor Paint | This product is made of specially modified epoxy resin, high-quality solvent, additive, special adhesion promoter, curing agent and other raw mater... |
Same products
 |
FT wax used for EVA-based hot melt adhesive | 卖方: Syntop chemical Co.,Ltd. | Fischer-Tropsch wax is a commonly used performance modifier in hot melt adhesives, especially for... |
 |
high melting point FT wax improve the heat resistance of adhesives | 卖方: Syntop chemical Co.,Ltd. | FischerTropsch wax is an alkane polymer produced from synthesis gas or natural gas via the Fische... |
 |
For hot melt adhesive high melting point FT WAX | 卖方: Syntop chemical Co.,Ltd. | The key advantage of high-melting-point Fischer-Tropsch wax in hot-melt adhesives stems from its ... |
 |
Diesel Injection Delivery Valve 1W6982 | 卖方: China lutong | Diesel Injection Delivery Valve 1W6982 Diesel Injection Delivery Valve 19AChris Diesel Injection... |
 |
High melting point FT wax used as plastic processing additives | 卖方: Syntop chemical Co.,Ltd. | Due to its high purity, low oil content, narrow melting range, high hardness, and excellent therm... |
