Metal Seated Gate Valve
Features of Metal Seated Gate Valve
The stem is permanently sealed by three independent seals, and if the seal wears out after long use, the gland bolts only need to be tightened;
Stem spherical stop-thrust, low friction resistance, so that the valve is light to open and close, low operating torque;
Major stem O-ring can be replaced with pressure in the pipe;
Epoxy resin sprayed on the inner and outer surface of the product, not easy to corrode.
Metal Seated Gate Valve Working Principle
Metal Seated gate valve vs resilient seatedgate valve, Usually both can be used on the water pipeline, reilient seated gate china valvemore for clean water pipeline, because the granular medium will cause damage to the rubber of the gate, while the metal seated gate valve is more widely used, the hardness of the bronze seat makes in the granular medium can also be very good to achieve the sealing effect and service life will not be greatly affected. But the metal seated gate valve production cycle is longer, the use of higher costs, so the choice between the two or according to the working conditions of the media conditions and budget to choose.
Metal Seated Gate Valve Installation and Commissioning
Metal seated gate control valvein the pipeline does not require frequent maintenance, depending on the time of use, the stem O-ring can be replaced periodically to reduce the possibility of leakage. For specific use, please consult Zeco Valve Group.
Metal Seated Gate Valve Material and Standard
Size Range: 2"~64"
Pressure Rating: 10bar ~ 25bar
Face to Face Dimensions: AMSE B16.10, EN558-1
Flange End Dimension: AMSE B16.5, AS4087, EN1092-2
Coating: WRAS approved Fusion Bonded Epoxy Coating
Inspection and Test: ISO 5208 / EN 12226-2
|
Part |
Material |
Standard |
|
Body |
Ductile Iron/ Cast Iron |
EN 1563/DIN 1693 |
|
Bonnet |
Ductile Iron/ Cast Iron |
EN 1563/DIN 1693 |
|
Trim |
Ductile Iron/ Cast Iron |
EN 1563/DIN 1693 |
|
Seat |
Bronze/Brass |
ASTM B62/ ASTM B148 |
|
O-ring |
EPDM / NBR |
ISO 4633 |
|
For materials options not listed, consult factory. Zeco manufactures valves in more than 50 different alloys. |
||
在线联系供应商
Other supplier products
 |
3 Inch Butterfly Valve | Description of butterfly valve 3 inch: ZECO 3 inch butterfly valve is a small diameter butterfly valve, usually manually operated, and the connect... |
|
|
Metal Seated Gate Valve | Features of Metal Seated Gate Valve The stem is permanently sealed by three independent seals, and if the seal wears out after long use, the gland... |
 |
Cryogenic Gate Valve | Description of Cryogenic Gate Valve: The main material of ZECO cryogenic gate valve is selected. Considering from the metallographic aspect, in ad... |
 |
Swing Check Valve | What is a Swing Check Valve? A Swing Check Valve is desinged to prevent the medium in the pipeline from flowing back. As pressure reaches zero, th... |
 |
Air Valve | ZECO is one of the leading check valve manufacturers china, China. ZECO check valveprovides non-slam closure, have a low head loss and close drip-t... |
Same products
 |
FT wax used for EVA-based hot melt adhesive | 卖方: Syntop chemical Co.,Ltd. | Fischer-Tropsch wax is a commonly used performance modifier in hot melt adhesives, especially for... |
 |
high melting point FT wax improve the heat resistance of adhesives | 卖方: Syntop chemical Co.,Ltd. | FischerTropsch wax is an alkane polymer produced from synthesis gas or natural gas via the Fische... |
 |
For hot melt adhesive high melting point FT WAX | 卖方: Syntop chemical Co.,Ltd. | The key advantage of high-melting-point Fischer-Tropsch wax in hot-melt adhesives stems from its ... |
 |
Diesel Injection Delivery Valve 1W6982 | 卖方: China lutong | Diesel Injection Delivery Valve 1W6982 Diesel Injection Delivery Valve 19AChris Diesel Injection... |
 |
High melting point FT wax used as plastic processing additives | 卖方: Syntop chemical Co.,Ltd. | Due to its high purity, low oil content, narrow melting range, high hardness, and excellent therm... |
