YJQ-W5 Adjustable hand crimp tool M22520/5-01 multifunctional plier used in electronic connectors
Specifications
YJQ-W5 is a standard adjustable hand crimp tool designed for the crimping of wires and contacts in electronic connectors.
GENERAL INFORMATION
YJQ-W5 is compatible with the M22520/5-01 which is widely used for crimping all kinds of ferrules, coaxial connectors, contacts, coalitions and wire terminal blocks. Interchangeable dies can be installed and fixed in a proper position with pins. If your application requirement is not already covered by one of our standard dies, our engineering department will be pleased to discuss a design to suit your needs.
Specifications
YJQ-W5 is a standard adjustable hand crimp tool designed for the crimping of wires and contacts in electronic connectors.
GENERAL INFORMATION
YJQ-W5 is compatible with the M22520/5-01 which is widely used for crimping all kinds of ferrules, coaxial connectors, contacts, coalitions and wire terminal blocks. Interchangeable dies can be installed and fixed in a proper position with pins. If your application requirement is not already covered by one of our standard dies, our engineering department will be pleased to discuss a design to suit your needs.
DIE INSTRUCTIONS
- Die installing
lAim the two half of die rail slots at the die rail and push shank of dies into holes.
lClose tool handle to ensure the dies are properly installed.
- Die removal
lKeep the handle of crimp tool in open position, place the die removal tool at the end of knockout pin and tap gently with small hammer. The die will be released from the front end of die holder. Then it can be removed by hand.
lClose the handle crimp tool, slide the die removal tool between die and tool body. Then open the handle with fast motion, the die will be release and can be removed by hand.
(Note: Die removal tool part number HX3-82 is furnished with crimp tool. If die removal tool is not available, a rod approximately 3/16’’ diameter X 13/4’’ long may be used.)
GAGING INSTRUCTIONS
l“GO” Gaging: keep the tool in fully closed position, insert the green “GO” gage end into the die cavity, it should be easy to enter, otherwise, the selector gear is incorrect.
(CAUTION! DO NOT CRIMP GAGE!)
l“NO GO” Gaging: keep the tool in fully closed position, insert the red “NO GO” end into the die cavity, it can’t pass through completely, otherwise, the selector gear is incorrect.
(CAUTION! DO NOT CRIMP GAGE!)
CAUTIONS
- Keep the crimping tool and other units clean and properly stored when not in use or no operator maintenance.
- Don’t try to immerse tools in cleaning solution or spray oil into tools to lubricate.
- If finding anomalies due to the incorrect ways, don’t attempt to disassemble tools or make repairs. Please stop using it and connect us as soon as possible, our company will offer complete refurbishing and recalibration services.
在线联系供应商
Other supplier products
 |
YJQ-W2Q Pneumatic crimp tool wire range 12-26AWG used in electronic connectors | Specifications YJQ-W2Q is a pneumatic crimp tool designed for the crimping of wires and contacts in electronic connectors. GENERAL INFORMATION 1.... |
 |
YJQ-W1A Adjustable aviation hand crimp tool M22520/2-01 multifunctional plier 20-32AWG electronic connectors | Specifications YJQ-W1A is a standard adjustable hand crimp tool designed for the crimping of wires and contacts in electronic connectors. GENERAL... |
 |
YJQ-W1Q Pneumatic crimp tool 20-32AWG electronic connectors M22520/2-01 | Specifications YJQ-W1Q is a pneumatic crimp tool designed for the crimping of wires and contacts in electronic connectors. GENERAL INFORMATION 1.... |
 |
YJQ-W1A Adjustable aviation hand crimp tool M22520/2-01 multifunctional plier 20-32AWG electronic connectors | Specifications YJQ-W1A is a standard adjustable hand crimp tool designed for the crimping of wires and contacts in electronic connectors. GENERAL... |
|
|
YJQ-W5 Adjustable hand crimp tool M22520/5-01 multifunctional plier used in electronic connectors | Specifications YJQ-W5 is a standard adjustable hand crimp tool designed for the crimping of wires and contacts in electronic connectors. GENERAL ... |
Same products
 |
GT-FM24-PLC填粉机机(3+9+9+3)三导管 | 卖方: 肇庆古雷特科技有限公司 | * 描述 GT-FM-PLC（6-48工位三导管）氧化镁粉灌装机，是在GT-FM-PLC（6-48工位双导管）的基础上改进而成。 双导管灌装机与三导管灌装机的主要区别如下： 三导管灌装机可以在一... |
 |
High Speed Flat Wire Coil Winding Machine for EV Traction Motor Manufacturing | 卖方: Eurion Automation Co., Ltd. | 高精度伺服控制系统：采用工控级电脑控制平台，配套进口伺服电机与减速机，确保运行高效、精准、稳定。 六轴联动结构设计：送线轴、绕线轴、排线轴及手臂成型轴独立控制、协同配合，实现多工序复合成型。 ... |
 |
GT-FM18-PLC灌装机(8+2+8)三导管 | 卖方: 肇庆古雷特科技有限公司 | * 描述 GT-FM-PLC（6-48工位三导管）氧化镁粉灌装机，是在GT-FM-PLC（6-48工位双导管）的基础上改进而成。 双导管灌装机与三导管灌装机的主要区别如下： 三导管灌装机可以在一... |
 |
48工位填粉机 GT-FM48 | 卖方: 肇庆古雷特科技有限公司 | * 描述FM灌装机适用于长长度、不同直径的管式加热器的灌装。 FM填充机填充的加热器具有高密度，根据直径、氧化镁粉末、填充速度，密度可达2.3g/cm3。 FM灌装机有双导管灌装机和三导管灌装机... |
 |
8工位填粉机 GT-FM8 | 卖方: 肇庆古雷特科技有限公司 | * 描述 FM灌装机适用于长长度、不同直径的管式加热器的灌装。 FM填充机填充的加热器具有高密度，根据直径、氧化镁粉末、填充速度，密度可达2.3g/cm3。 FM灌装机有双导管灌装机和三导管灌装... |
