MOV Block for Distribution Arrester

TGE developed D36 & D42 series glass coating MOV which be suitable for distribution arresters according to IEC60099-4 (2014) in 2018. Based on the proven technique of high-performance metal oxide varistor, a special new type of metal oxide varistor can be used in heavy-duty distribution arresters has been successfully developed recently by TGE for the purpose of optimization of the electrical and economic performance of the new MOV with a diameter of 36mm & 42mm, that signifies not only its electrical performance meets the requirements, but also it can be led to cost reduction of arrester by means of smaller arrester dimension.

MOV Block for Distribution Arrester Advantages

1

Excellent performance in the high current test: TOV reached 1.25Ur and 1s was higher than the standard 1.2Ur and 0.1s.

2

Higher protection level: TOV reached 1.25Ur and 1s was higher than the standard 1.2Ur and 0.1s.

3

High performance in 8/20µs charge test: Ures change is within 3% and Ures change is within 1% after Qrs 0.4C charge test with 8/20µs waveshape for TGE D36.

4

High performance in short circuit test: TGE wound core for customer passed 16kA short circuit test.

5

Stable aging performance.

6

High energy absorption capability.

How Does MOV Block for Distribution Arrester Work?

First of all, the stability of the electrical parameters of metal oxide varistor mov under continuous operating voltage.

The artificial accelerated aging test proves that in the life cycle of the MOV, its power consumption shows a declining trend with time. This means that in the long-term operation of the MOV or arrester, the power consumption or heat generated by itself will not gradually increase, so the zov movor arrester is in a stable state. On the other hand, when the MOV or arrester is subjected to continuous operating voltage for a long time, the influence of the change in ambient temperature on the power consumption or resistive current of the MOV is also a factor that affects the operational stability of the MOV or arrester. Since the power consumption or resistive current of the MOV has a positive temperature coefficient, anyway, as the temperature increases, the power consumption or resistive current will show an increasing trend. But in spite of this, the improvement of manufacturing technology can make the change of power consumption or resistive current with temperature as small as possible, which is conducive to the safe operation of the arrester. The figure shows that the aging characteristics of the D36& D42 series MOVs show that the power consumption increases monotonously as the application increases. The figure shows the change in power consumption of the MOV at different temperatures. Especially at a temperature of 190 ° C, the power consumption of the MOV sheet remains low. This is particularly important for the design of lightning arresters. When operating load or TOV test, the temperature rise of the MOV is very high due to the large energy absorbed by the MOV, and only when the high temperature power consumption remains low, it is

Specification of special metal oxide varistor for heavy duty distribution arrester easier to reach the heat under the recovery voltage or MCOV voltage stable. After the surge arrester in operation absorbs overvoltage energy, due to the lower high-temperature power consumption of the MOV, the heat generation of the surge arrester is lower, which is more conducive to the safe operation of the surge arrester

Secondly, the stability of the electrical parameters of the MOV sheet after being subjected to different pulse currents. The most obvious characteristic of the mov blocks after undergoing a large pulse current and absorbing the corresponding energy is that the temperature rise and the reference voltage leakage current or power consumption and residual voltage after cooling have a certain amplitude change from the value before the pulse current. Contactmetal oxide varistor manufacturerTGE for more product details.

For more information about zov varistor, please feel free to contact us!

Other supplier products

	D42 Series MOV Block for Substation Arrester	D42 Series MOV Block for Substation Arrester The D42 Series MOV for Substation Arrester is designed for heavy-load surge protection in 35kV substa...
	Arrester Core	The mov coreis a form of electrical equipment utilized for shielding electrical systems against harm caused by lightning strikes or other types of ...
	D78H35.4 MOV Block for DC Arresters	Note: The nouns, parameters and corresponding test methods in this parameter list conform to the standards of IEC60099-4:2014 and GB11032-2020. T...
	High Gradient MOV Block for GIS Arresters	High Gradient MOV (Metal Oxide Varistor) GIS Arresters are surge arresters designed specifically to protect sensitive GIS (Gas Insulated Switchgear...
	D85 Series High Gradient MOV Block for GIS Arresters	The D85 Series High Gradient MOV for GIS Arresters is a must-have for any 330kV GIS surge arrestersystem. This MOV varistor provides ultra-high gra...

供应产品

Same products

	MOV Block for Line Surge Arrester	卖方: Xi'an Tiangong Electric Co.,Ltd	MOV stands for Metal Oxide Varistor. It is a type of surge arrester that is used to protect elect...
	MOV Blocks	卖方: Xi'an Tiangong Electric Co.,Ltd	The mov blocks, otherwise referred to as zinc oxide varistors or energy blocks, serve as the core...
	MOV Block for Distribution Arrester	卖方: Xi'an Tiangong Electric Co.,Ltd	TGE developed D36 & D42 series glass coating MOV which be suitable for distribution arresters...
	D99 Series MOV Block for Substation Arrester	卖方: Xi'an Tiangong Electric Co.,Ltd	The D99 Series MOV for Substation Arrester is a state-of-the-art lightning arrester designed to p...
	D85 Series High Gradient MOV Block for GIS Arresters	卖方: Xi'an Tiangong Electric Co.,Ltd	The D85 Series High Gradient MOV for GIS Arresters is a must-have for any 330kV GIS surge arreste...