RTV-1 Silicone Rubber
RTV-1 Silicone Rubber
RTV-1 siliconeis a condensedrubber that is gradually cured from outside to inside by contacting with moisture in the air.rtv grease-1 silicone rubber are used in bonding, sealing, encapsulating photovoltaic module components including photovoltaic frame, junction box and micro-inverter, power industry including circuit boards, electronic components, light emitting diode industry including lamp beads, lamp cap and light bar, home appliance including air conditioner, fridge, washing machine, and microwave oven, induction cooker, new energy vehicle including electronic component. GOLOHORTV-1 silicone rubbersare designed to provide long-term bonding, sealing, encapsulating and protection against moisture, environmental degradation, mechanical and thermal shock, heat dissipation and vibration where a room-temperature-curing product is preferred.
When usingRTV-1 silicone rubber, all surfaces must be clean and dry. Degrease and wash off any contaminants that could impair adhesion. Suitable solvents include isopropyl alcohol, acetone, or methyl ethyl ketone. Apply a bead ofRTV-1 silicone rubberto one of the prepared surfaces, then quickly cover with the other substrate to be bonded. On exposure to moisture, the freshly applied material will “skin over” in about 10 to 15 minutes at room temperature and 50% relative humidity. Any tooling should be completed before this skin forms. The surface is easily tooled with spatula. GOLOHO RTV-1 silicone rubbers will be tack free in about 5 to 60 minutes. After skin formation, cure continues inward from the surface. In 24 hours (at room temperature and 50% relative humidity), GOLOHORTV-1 silicone rubberswill cure to a depth of 2 to 3 mm. Very deep sections, especially when access to atmospheric moisture is restricted, will take longer to cure completely. Cure time is also extended at lower humidity levels. Before handing and packaging bonded components, users are advised to wait a sufficiently long time to ensure that the integrity of the adhesive seal is not affected. This will depend on many factors and should be determined by user for each specific application.
在线联系供应商
Other supplier products
 |
Addition Silicone Rubber | GOLOHO heat cured silicone rubberproduces no by-products in the curing process, allowing their use in deep section and complete confinement. GOLOHO... |
 |
High Performance Silicone Adhesive/Sealant - 3334 | FEATURES OF heat and water resistant sealantheat proof silicone adhesive- 3334 Convenient: one-part, deoximation, rapid cure at room temperature Ne... |
 |
Grease | High performance thermal grease GOLOHO Silicone Grease are adhesive thermal compounds like silicone materials, heavily filled with heat-conductive ... |
 |
High Performance Silicone Adhesive/Sealant - 3334 | FEATURES OF GOLOHO-3334 Convenient: one-part, deoximation, rapid cure at room temperature Neutral, no corrosion to metal, anti-yellowing. Excellent... |
 |
Two-Part, 1 To 1 Mix Ratio Transparent Silicone Gel - 324C-AB | SPECIAL FEATURES OF GOLOHO-324C-AB 1:1 Two-part, 1:1 mix ratio Low viscosity Room temperature accelerated cure, no small molecule release Suitable ... |
Same products
 |
LC12 Two-Component Solvent Free Silicone Conformal Coating | 卖方: Nanjing Silfluo New Material Co., Ltd. | Conformal Coating, also called silicone coating pcbelectronic circuit board protection oil, coati... |
 |
LA-17 Polyether Modified Short Chain Polysiloxane | 卖方: Nanjing Silfluo New Material Co., Ltd. | Polyether modified trisiloxaneshort chain polysiloxane. Compared to trisiloxane surfactant,it has... |
 |
LA-14 A Modified Trisiloxane and an Silicone Surfactant | 卖方: Nanjing Silfluo New Material Co., Ltd. | (It is a substitution of Silwet ECOand Xiameter(R) OFX-0309) A modified Trisiloxane and an silico... |
 |
LA-11 A Modified Trisiloxane and an Silicone Surfactant | 卖方: Nanjing Silfluo New Material Co., Ltd. | (It is a substitution of silwet l 77) A modified Trisiloxane and an silicone surfactant with supe... |
 |
KSS Potassium Diphenylsulfone Sulfonate | 卖方: Nanjing Silfluo New Material Co., Ltd. | KSS is a high heat stable PC additive. Equivalents to FR2025, EF-42. Description of KSS Potass... |
