Addition Silicone Rubber
Addition Silicone Rubber
GOLOHOproduces no by-productsrtv greasein the curing process, allowing their use in deep section and complete confinement.GOLOHOAddition Silicone Rubberhas two types, one is one-part silicone rubber, the other is two-part silicone rubber.One-part additionsilicone rubberis heat-cured, thermally conductive adhesives. These adhesives will develop good, primerless adhesion to a variety of common substrates including metals, ceramics, epoxy laminate boards, reactive materials and filled plastics.For most users, GOLOHO Addition Silicone Rubber should be operational over a temperature range of -45-200℃ for long periods of time. However, at both the low and high-temperature ends of the spectrum, the behavior of the materials and performance in particular applications can become more complex. So additional tests should be executed before use.
Long-term, reliable protection of sensitive circuits and components is important in many of today’s delicate and demanding electronic applications. Addition-curesiliconeshould be cured at 100℃ or above the cure rate is rapidly accelerated with heat. Addition-curing materials contain all the ingredients needed forcurewith no by-products from the cure mechanism. Deep-section or confined cures are possible. Cure progress evenly throughout the material. One-part addition-cure silicone rubber should be kept tightly closed at low temperature (below 5℃).Two-part addition silicone rubberareroom temperature or heat acceleratedcure. When the two components are thoroughly mixed in a 1 to 1 mix ratio, cure reaction begins. Initially,cureis evidenced by a gradual increase in viscosity, followed by gelation and conversion to a solid, flexible elastomer, which is well suited for the protection of electrical/electronic applications. They cure without exotherm at a constant rate regardless of sectional thickness or degree of confinement. Thus, deep section and complete confinement are preferred. At the same time, no by-products are produced in thecureprocess. Two-part addition-cure silicone rubber should be kept tightly against oxygen and moisture at room temperature.
在线联系供应商
Other supplier products
 |
High Performance Silicone Adhesive/Sealant - 3334 | GOLOHO-3334is a kind of heat proof silicone adhesive. FEATURES OF GOLOHO-3334 Convenient: one-part, deoximation, rapid cure at room temperature Ne... |
 |
High Performance Silicone Adhesive/Sealant - 3334 | FEATURES OF HEAT RESISTANT SILICONE GLUE. Convenient: one-part, deoximation, rapid cure at room temperature Neutral, no corrosion to metal, anti-ye... |
|
|
Addition Silicone Rubber | Addition Silicone Rubber GOLOHOproduces no by-productsrtv greasein the curing process, allowing their use in deep section and complete confinement.... |
 |
Addition Silicone Rubber | GOLOHO Addition Silicone Rubber produces no by-products in the curing process, allowing their use in deep section and complete confinement. GOLOHO... |
 |
Two-Part, 1 To 1 Mix Ratio Transparent Silicone Gel - 324C-AB | SPECIAL FEATURES OF GOLOHO-324C-AB 1:1 Two-part, 1:1 mix ratio Low viscosity Room temperature accelerated cure, no small molecule release Suitable ... |
Same products
 |
LC12 Two-Component Solvent Free Silicone Conformal Coating | 卖方: Nanjing Silfluo New Material Co., Ltd. | Conformal Coating, also called silicone coating pcbelectronic circuit board protection oil, coati... |
 |
LA-17 Polyether Modified Short Chain Polysiloxane | 卖方: Nanjing Silfluo New Material Co., Ltd. | Polyether modified trisiloxaneshort chain polysiloxane. Compared to trisiloxane surfactant,it has... |
 |
LA-14 A Modified Trisiloxane and an Silicone Surfactant | 卖方: Nanjing Silfluo New Material Co., Ltd. | (It is a substitution of Silwet ECOand Xiameter(R) OFX-0309) A modified Trisiloxane and an silico... |
 |
LA-11 A Modified Trisiloxane and an Silicone Surfactant | 卖方: Nanjing Silfluo New Material Co., Ltd. | (It is a substitution of silwet l 77) A modified Trisiloxane and an silicone surfactant with supe... |
 |
KSS Potassium Diphenylsulfone Sulfonate | 卖方: Nanjing Silfluo New Material Co., Ltd. | KSS is a high heat stable PC additive. Equivalents to FR2025, EF-42. Description of KSS Potass... |
