Acrylic polyol resin MT-7152-80
Introduction
Characterization
Acrylic polyol resin designed for high solid low VOC ACE top coating
Form supplied
Form supplied is approximately 80% in butyl acetate
Applications
Suitable for 2K PU coatings providing outdoor durability, high solid and low VOC.
Property: Hydroxylvalue, on solid
Value: 83
Unit of measurement :mg KOH/g
Method :TM-2432
Solubility / thinnability
can be thinned with aromatics, esters and ketones solvent.
Storage
The resin should be stored indoors in original, unopened and undamaged container in a dry place at storage temperature between 5- 30 °C. Exposure to direct sunlight should be avoided.
Storage time
Covestro represents that, for a period of 6 months (180 days) following the day of shipment as stated in the respective transport documents, the product will meet the specifications or values set forth in section “specifications or characteristic data” above, what ever is applicable, provided that the product is stored in full compliance with the storage conditions set forth in and referenced under section “storage” above and is otherwise handled appropriately. The lapse of the 6 months (180 days) period does not necessarily mean that the product no longer meets specifications or the set values. However, prior to using said product, Covestro recommends to test such a product if it still meets the specifications or the set values. Covestro does not make any representation regarding the product after the lapse of the 6 months (180 days) period and Covestro shall not be responsible or liable in any way for the product failing to meet specifications or the set values after the lapse of the 6 months (180 days) period.
在线联系供应商
Other supplier products
 |
77PD (4030) CAS 3081-14-9 N, N’- bis-(1,4- Dimethylpentyl)-p-Phenylenediamine | Introduction Chemical Name:N, N’- bis-(1,4- Dimethylpentyl)-p-Phenylenediamine CAS NO.:3081-14-9 Product Specification: Appearance ... |
 |
Thermal interface material | Thermal conductive sealant There are two types of thermal conductive joint fillers: silicon-based and non silicon. They are usually two-component ... |
 |
CAS 54914-85-1 EGTE 1,2-Bis(3-methylphenoxy)ethane | Introduction CAS:54914-85-1, 54914-85-1 – Names and Identifiers Name 1,2-Bis-(3-methyl-phenoxy)ethane Synonyms F-203(EGTE)1,2... |
 |
Styrene CAS 100-42-5 | Introduction Styrene SDEB is a type of styrene produced by catalytic dehydrogenation of ethylbenzene. It is used to manufacture polystyrene, ABS p... |
 |
7PPD CAS 3081-01-4 | 3081-01-4 –Names and Identifiers Name N-(1,4-dimethylpentyl)-N’-phenylbenzene-1,4-diamine Synonyms Einecs 221-374-3SANTOF... |
Same products
 |
Epoxy/Polyester Powder Coatings | 卖方: Standard International Group (HK) Limited | Feature: -Good bond ability and mechanical performance -Smooth and glossy -Certified chemical ... |
 |
Polyester Clear Powder Coatings | 卖方: Standard International Group (HK) Limited | This series of product are made of polyester resin (as hardener) and highly transparentmaterials.... |
 |
Acrylic Clear Powder Coatings | 卖方: Standard International Group (HK) Limited | Feature: -Excellent exterior exposure durability -Excellent durable high gloss -Excellent clar... |
 |
Polyurethane Powder Coatings | 卖方: Standard International Group (HK) Limited | Feature： -Excellent exterior exposure durability -Good flowing -Excellent chemical resistance ... |
 |
MDF Powder Coating | 卖方: Standard International Group (HK) Limited | Feature： -Environmental friendly -No solvents and volatile organic compounds involved which are... |
