.

Oil filled power transformer

Transformer is an important electrical equipment that must be used in our production and life. For transformer, it can control the voltage and current in the circuit, realize the voltage stability in the circuit, and improve the greater effect in the power equipment, which is more conducive to production and life. Transformer in the troubleshooting is to pay attention to a lot of problems, common maintenance methods according to the different types of transformer comprehensive choice of maintenance methods, the following is the transformer in the maintenance of the relevant issues for your reference, following thewould like to share us thedetail:

Before repair, a layer of transparent tape is tightly wrapped around the windings outside the loop transformer IK and the high and low voltage isolation places. This tape is a kind of insulation tape that can withstand high temperature and is difficult to find, so try to keep it intact when removing the ring transformer tape, not to lose. Because the inner ring of the annular transformer is not large and there is no opening, it can only pass through the inner ring one by one when disassembling enameled wire, so it is better to make a winding board. 20 (length of 15 m, width can be appropriate changes, according to the volume of ring transformer inner ring generally desirable radius of inner ring size is good, and each open a concave n at both ends, it can prevent the enameled wire loose, can use thin plywood or plastic material, solve the damaged ring transformer outer insulating tape, can see the secondary windings, before the split at the end of the secondary windings, to make repairs to be fast and accurate, can be examined first ring transformer primary winding damage location where, due to the secondary winding is good, can through the secondary winding under the seam between the enameled wire to see whether there is obvious in the primary winding burn. Sometimes after the primary winding is burned out, there will be an obvious black spot in the fault position, or the high and low voltage isolation tape also burned through, so that you can determine the starting and dismantling end of the secondary winding, if the primary winding open point in the secondary lead end near one end, can be dismantled from this end, can get twice the result with half the effort. When the fault point cannot be found, it is necessary to carefully remove the enameled wire round and round at one end, and wrap the removed enameled wire directly on the winding board. If there are more than one winding, more than one winding board should be used.

In the process of disassembly, attention should be paid to the damaged part of primary winding while disassembling. When disassembling to the damaged part, it should stop, and carefully cut the tape outside the primary winding to expose the breaking point. The resistance between the breaking point and the two input leads is measured with the multimeter 10Q, and the resistance between the input lines of the annular transformer is basically equal to the sum of the above two resistance values. If a certain resistance value is a, it means there is still a breaking point, and if it is too small, it means there is a short circuit. When it is proved that the fault point is only there, partial repair can be carried out, as long as a broken enameled wire of the same specification is well connected and the insulation sleeve is covered. When wiring must be in the enameled wire insulation layer bright open interface, remove the number of rings should be filled back to the number of rings, if the iron core insulation tape burned through, must find a large enough insulation paper wrapped and then rewound. Joint should be bound into twist shape and then repair welding, not only by the method of simple lap weld ring transformer primary winding yan burned, it is necessary to all new winding down, m around the primary winding, how many will be subject to real number, the number of turns and the vast majority of transformer data displaying, sun can cut after the root number, also on the core in a direct count, because of the winding is wound, disjoint between line, points easily. The disassembly order is: first remove the secondary winding, the general secondary winding enameled wire is intact, can be used again, and then remove the insulation tape, then remove the primary winding, remove burned insulation, and replace the insulation tape if necessary. How to wind the wire is also a difficulty, because hand T:. It is impossible for a large coil of enameled wire to pass through the inner hole of the annular transformer core. Amateur conditions, can weigh it first remove the original primary winding of the enameled wire weight, then from the new phase, the landscape of the heavy around the winding board first, not enough to prevent, pre - more than 5 to 10% of the enameled wire, so that it can be winding, winding to generally the same as the original, need not to separate polar winding around good later must not be enameled wire overlapping, stretched as far as possible, don't enameled wire loop, the line between the M to arrange all. After the primary winding is wound according to the original number of turns, the excess should be cut off, welded the power lead wire, wrapped with tape, ran back to the original secondary winding, as long as the original line spacing to wrap the defect can be wrapped, the last outer layer also wrapped with tape, conditions can dip paint baking, finally electrification test.

maintenance must pay attention to the common methods and some major steps, only is the steps and methods to master flexible, so the effect of the transformer can have greater improvement and related performance of transformer and transformer maintenance steps our transformer manufacturer will discussed with you, welcome to communicate with us!



在线联系供应商

至: Baoding Zhongyi Electrical Material Manufacturing Co.,Ltd.
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

Circuit Breaker Switchgear
Circuit Breaker Switchgear High and Low Voltage Switchgears GCK series low voltage draw out switchgearis applicable for three phase four wire/five wire AC power system with r...
Amorphous alloy power transformer China
Amorphous alloy power transformer China is a new type of energy saving transformer made of a new magnetic conducting material (amorphous alloy). It is more than 70% lower than the no-loa...
Why are transformers mostly used in parallel?
Why are transformers mostly used in parallel? Transformer in the process of running has run in parallel and series operation, but are used in most of the use of parallel operation, parallel o...
Working principle of transformer
Working principle of transformer Three phase transformer Manufacturershares that transformer is a kind of electric appliance that transfers electric energy or transmits signal fr...
Dry type Power Transformers
Dry type Power Transformers Product Description SG (B) 10 series of non-encapsulated H-class dry-type power transformersadopt the special process technology of German (MORA) d...
供应产品

Same products

d6-35 Oil-Immersed Oil-Filled Type Potential Voltage Transformer PT 27.5kv, 35kv, 66kv, 72.5kv, 110kv, 126kv, 220kv, 245kv
d6-35 Oil-Immersed Oil-Filled Type Potential Voltage Transformer PT 27.5kv, 35kv, 66kv, 72.5kv, 110kv, 126kv, 220kv, 245kv 卖方: Chongqing Enrich Engineering and Technology Co., Ltd 35-220kV Oil-filled/Oil-immersed type potential/voltage transformer   JD6-35 Oil-immersed type vo...
Lb6-110 Lb7-220 Type Oil-Immersed Oil-Filled Hair-Pin Type Fully sealed Structure Current Transformer CT with Protection Class 35kv, 66kv, 110kv, 220kv, 330kv power system
Lb6-110 Lb7-220 Type Oil-Immersed Oil-Filled Hair-Pin Type Fully sealed Structure Current Transformer CT with Protection Class 35kv, 66kv, 110kv, 220kv, 330kv power system 卖方: Chongqing Enrich Engineering and Technology Co., Ltd LB6-35(33)(TA,TH)(W1,W2,W3)/LABN6-35 Oil-immersed/filled outdoor single phase current transformer...
Lxk Indoor Electromagnetic Type Round Toroidal ring Type Epoxy Resin Open-Close Split Core Core Balance Type Zero Sequence Current Transformer CT Residual Current Transformer CT Earthing Grounding Pro
Lxk Indoor Electromagnetic Type Round Toroidal ring Type Epoxy Resin Open-Close Split Core Core Balance Type Zero Sequence Current Transformer CT Residual Current Transformer CT Earthing Grounding Pro 卖方: Chongqing Enrich Engineering and Technology Co., Ltd LXK zero sequence current transformer   Model description LXK-φ80(100,120,200,300) L: Current tra...
SG(B) 10 Type 10kv Series Non Encapsulated Coil Transformer
SG(B) 10 Type 10kv Series Non Encapsulated Coil Transformer 卖方: YueBian Electric Co.,Ltd General introduction of SGB10 Cast Resin Transformer: Cast Resin Transformer, is a kind of dry ty...
SFZ11 Type 35kv Series On-Load Regulator Transformer
SFZ11 Type 35kv Series On-Load Regulator Transformer 卖方: YueBian Electric Co.,Ltd General introduction of onload transformer: This transformer meets the criteria of GB1094 and GB/...