NTC Thermistors Temperature Sensor Probe Assemblies

NTC Thermistors Temperature Sensor Probe assembly, housed in stainless steel, copper, plastic,Al, for HVAC, food processing, industrial control application.

NTC Thermistors Temperature Sensor Probe Description

NTC Thermistor can be assembled in housing in a variety of configurations for temperature sensing, measurement, detection, indicator, monitoring and control. Thermistor temperature sensor probe assemblies can conveniently attach to or be an integral part of any system to monitor or control temperature.The choice of assembly is dependent on the application. The primary factors which determine the optimum configuration of a thermistor assembly are the operating environment, mounting, time response and minimum dissipation constant.
The two factors which do vary considerably with thermistor sensor probe assembly design are time constant and dissipation constant. The time constant will typically be of greater duration in encapsulated thermistors. This is, of course, due to additional mass surrounding the thermistor element; therefore, extending the thermal transfer time. Dissipation constant will also be greater in assemblies. The additional housing mass serves well as a heat sink. Greater power is therefore required to induce self-heating. Both time constant and dissipation constant will vary with the selected thermistor and housing. Heat transfer properties of the housing, thermistor location, mass and wire type determine these constants.
Applications for temperature sensing include air temperature sensors, surface temperature sensors and immersion temperature sensors. Housings for air temperature sensors are often simple, inexpensive devices such as molded plastic shells, deep-drawn brass or aluminum cylinders, or even stainless steel tubes. Surface temperature sensors are designed to match the contour of the surface to be sensed, whether it's flat, curved, or round. Mounting holes or clips are often used to simplify installation of the sensor. Immersion temperature sensors are designed so that the sensing element will be surrounded by the medium to be sensed, often times a liquid. The sensing portion will normally protrude through a hole or orifice while a portion of the assembly will remain outside the medium to allow for the signal to be read. Immersion housings are usually threaded to allow them to be screwed into a hole or opening. Immersion part requests to be liquid and humidity prevention.
The material used for the housing will be dependent upon the temperature range needed, response time, cost, and special considerations such as UL, FDA or NSF requirements in food and/or medical applications. Some of the materials available include stainless steel, copper, plastic, teflon, brass, aluminum, epoxy and heat shrinkable tubing.

Other supplier products

	Flanged stainless steel thermistor probe	Application: thermistor temperature sensor probe assembly for standard domestic oven, microwave oven, electric cooker, roaster, toaster, industrial...
	ABS plastic freezer thermistor temperature sensor	Application: Thermistor temperature measurement for refrigerator, freezer, air conditioner, floor heating, and other HVAC application, etc. ABS Pl...
	Threaded stainless steel tube thermistor temperature sensor	Threaded stainless steel tube thermistor temperature sensor probe for temperature measurement of liquid, water, air, etc. Ideal for vessel and pip...
	Pointed tip stainless steel NTC thermistor temperature sensor	Stainless Steel Housing Immersion Penetration Probe. Pointed tip stainless steel NTC thermistor temperature sensor features Long stainless ste...
	NTC Thermistors Temperature Sensor Probe Assemblies	NTC Thermistors Temperature Sensor Probe assembly, housed in stainless steel, copper, plastic,Al, for HVAC, food processing, industrial control app...

供应产品

Same products

	Downhole Cable Protector, Mid-Joint Cable Protector	卖方: Qingdao Banghua Wire & Cable Co., Ltd	ESP Cable Solutions Co., Limited(ESPCS) is the most professional manufacturer for cable protector...
	Stamping cable protector, ESP Cable Protector	卖方: Qingdao Banghua Wire & Cable Co., Ltd	ESP Cable Solutions Co., Limited(ESPCS) is the most professional manufacturer for cable protector...
	Cross-coupling cable protector(Clamps)	卖方: Qingdao Banghua Wire & Cable Co., Ltd	ESP Cable Solutions Co., Limited(ESPCS) is the most professional manufacturer for cable protector...
	Cable Markers	卖方: Wuhan MZ Electronic Co.,Ltd	Cable Markers Characteristics: The EC type cable marker is for accommodates various cable diame...
	HRTC-N1 Control Modules	卖方: Tinko Instrument (Suzhou) Co., Ltd.	Tinko HRTC-N is still an LCD liquid crystal display and supports functions such as self-tuning/so...