Car Knock Sensors
The car aftermarket knock sensoris an AC signal generator, which can detect the speed and position of the rotating shaft, vibration or mechanical pressure. It's also a piezoelectric device. They are made of special materials that can sense mechanical pressure or vibration, for example, AC voltage can be generated when the engine starts knocking.
When the engine vibrates or knocks, the piezoelectric ceramics produce a voltage peak. The greater the knock or vibration, the greater the peak. The engine control unit ECU processes the received signal from the automotive knock sensors. If it judges that knock occurs, it will delay the ignition time and prevent further knock. When ECU does not receive the signal from the automotive knock sensors, it will advance the ignition time to ensure the best power output of the engine.
The car knock sensorfrom MAPMS auto sensors provides knock signal to the ECU and reminds ECU to readjust the ignition timing to prevent further knock.
Knock SensorsFeatures
Accurately measure engine shake.
Precise adjustment of ignition advance angle.
Durable and not easily damaged.
What Are the Symptoms of a Bad Auto Knock Sensor?
Auto Knock Sensor is used to measure the engine jitter and adjust the ignition advance angle when the engine produces knock. If there is a fault, the engine deflagration signal cannot be detected and the ignition time cannot be postponed automatically. Judge whether there is a fault through the following phenomena.
Knock Engine of automotive knock sensor
When the engine is working, engine knock will be caused by excessive ignition time advance (ignition advance angle), engine load, temperature and fuel quality. In case of knock, before the piston moves to TDC, the light one will produce noise and reduce the power of the engine, the heavy one will damage engine mechanical parts.
ECU Cannot Monitor the Degree of Deflagration
In case of damaged, ECU cannot monitor the degree of deflagration, it will reduce the ignition advance angle, when ECU detects that the engine has deflagration through the deflagration sensor, so it is wrongly judged that there is no deflagration. In this case, ECU will increase the ignition advance angle and cause the engine to work rough and shake due to deflagration.
Automatic Delay Ignition Time
Automatically delay the ignition time to prevent engine detonation. Therefore, the engine will be in the working state of ignition delay. The fuel consumption will increase, combustion energy rate will decrease, and engine power will decrease.
If you need any kinds of car spares and parts, please contact us, as one of the most professional auto spares suppliers, MAPMS is willing to offer you high quality products.
在线联系供应商
Other supplier products
Rear Wiper Blades | The rear wiper blade armis the wiper of the rear windshield of the vehicle, which is usually equipped on SUVs, MPVs, hatchbacks. The influence of h... | |
Neutral Safety Switches | The neutral safety switch relay is one of the vehicle safety switches to prevent accidents, which plays a role in safety protection. When the vehic... | |
Auto Relays | Auto off relay control higher voltages or currents by using lower voltages or currents. When a certain voltage or current is applied to both ends o... | |
LED Headlight | For automobiles, led head light bulbsSources to have the advantages of energy-saving, low cost, long life, good durability, the small size of LED c... | |
Fuel Level Sensors | The fuel pump and fuel level sensoruses the principle of the magnetic field generated by the ferrite magnet to control the on-off of the reed switc... |
Same products
Hangzhi CAFR-A-NP Series PCB Current sensor | 卖方: Shenzhen Hangzhi Precision Electronics Co., Ltd | CAFR-A-NP系列是航智自主研发的可焊接在PCB电路板上的电流传感器,基于磁通门技术,可实现直流电流和交流电流的隔离测量。 测量范围:±6A至±50A。精度:&... | |
Hangzhi CIT High Precision Split Core current transducer | 卖方: Shenzhen Hangzhi Precision Electronics Co., Ltd | CIT系列高精度分体式电流传感器是航智基于磁通门技术开发的,可实现直流电流和交流电流的隔离测量。 测量范围:±100A至±1500A。精度:0.05%。线性度:0.... | |
BMS300 Automotive Current Sensor Transducer | 卖方: Shenzhen Hangzhi Precision Electronics Co., Ltd | BMS300磁通门传感器由励磁磁环和控制电路组成,正常情况下,控制电路产生固定的励磁电流频率,使磁芯交替处于最大饱和点,当测量电流流过时,通过检测饱和点的对称性来测量一次电流。 BMS系列适用... | |
AIT6000-SG High-Precision Current Sensor Transducer, Accuracy 50ppm | 卖方: Shenzhen Hangzhi Precision Electronics Co., Ltd | AIT6000-SG在现有的直流传感器技术基础上,采用了多点零磁通技术体系和高频纹波传感通道,在全带宽范围内具有较高的增益和测量精度。 关键技术励磁闭环控制技术自励退磁技术多点零磁通技术温控补... | |
DIT300-SG high-precision digital current sensor | 卖方: Shenzhen Hangzhi Precision Electronics Co., Ltd | 航智DIT300-SG是一款300安培高精度数字电流传感器,精度为200ppm(200百万分之一)。 该高精度直流传感器采用多点零磁通技术体系,实现了励磁磁通、直流磁通、交流磁通的零磁通闭环控... |