ATE-2 LED驱动器自动测试系统
ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation and nice-looking, the workers can operate it at very short time. This system can meet the requirements of IEC62384, GB24825-2009 and other relative standards.
Characteristics:
•This equipment adopts the special designed electronic load to imitate the V-I curve of LED.
•The normal LED driver has the disadvantage of high ripple, so it will have big deviation when it drives the traditional electronic load. For this equipment, the electronic load is update, so that to approach the real LED load.
•This system contains a programmable frequency conversion power supply to ensure fast switch and choose the input voltage and frequency of tested driver.
•The test equipments, electronic load and programmable frequency conversion power supply in this system are special developed and designed to meet the LED driver test requirements.
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection.
•It can test 4 LED drivers input and output at one time.
•The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer.
•Enable to print out the series number and parameters of sub-quality products by working with a micro-printer,
•Enable to achieve the barcode record function by working with a barcode scanner.
•The test report can be saved as Excel file for consult, statistic and analysis purpose.
•Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
System function:
•Low voltage test and surge current test:
Full-load test includes:
Input: Voltage, current, power, power factor, frequency, harmonic and 2 to 11 times harmonic component
Output: voltage, current, power, ripple wave, efficiency
Steady state test includes:
Steady state 1, steady state 2, steady state 3. The chopped wave of power (enable to test dimming lights), voltage, and frequency in each state can be set separately; the other parameters are same as the full-load test.
Linear adjustment rate test; load adjustment rate test
•Over output voltage (current) protection test, under output voltage (current) protection test
•Output shorten circuit protection test, output open circuit protection test
•Stabilization time test; cut off time test
•Capacity discharge function
•Barcode record function
Specifications:
| Item | Test Range | Tolerance | Test Condition |
| Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) |
45~65Hz sine-wave |
| DC: 3～500V | |||
| Current | AC: 5mA～2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Power Factor | 0.000～1.000 | ±(0.002+0.001/reading+1digit) | |
| Frequency | 45Hz～65Hz | ±0.1% Reading | |
| Harmonic | Total harmonic, and 2-11 times harmonic component | ±(0.1% range+5% Reading) | |
| Surge Current | 50mA～100A | ±(0.5% range+0.5% range+1digit) | Square wave with pulse width greater than 10 10μs Calibration validity: 12month |
| Lamp Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) | 45~65Hz sine-wave Calibration validity: 12moths |
| DC: 3～500V | |||
| Lamp Current | AC: 5mA~2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Lamp Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Ripple Current | Max: 5mA～8A | ±(1%reading+1%range) | 20-70kHz sine-wave |
Note:
•Fundamental harmonic of voltage, current, lamp voltage, lamp current (AC) is 45Hz~65Hz. Frequency range is 45Hz~1MHz
•The frequency range of ripple current is 45Hz~1MHz.
you may surf our website of our company to get more information in here:
在线联系供应商
Other supplier products
 |
LPCE-1 CFL&LED高精度快速光色电综合测试系统 | 产品简介： LPCE-1系统适用于节能灯、卤素灯、银光灯、HID、CCFL以及LED等各类光源的对于光色电参数的检测。主机（LMS-5000光谱仪）是一款应用非常广泛的光谱仪，保持传统高精度机械扫描方式的同时大大提高了测试速度，380nm-800nm全波段扫描仅需10S。采用标准RS-232通... |
 |
KH3962 EMI测试系统|传导干扰测试系统 | KH3962电磁兼容·传导干扰测试系统是全自动的测试接收机，是进行EMl测试的主要工具。机器使用了全封闭式结构，机身采用导电性很强的材料，屏蔽效果极好，由于采用了新技术和新工艺，从根本上解决了自身干抗的问题。其测量结果为国际通用报告格式。该测量系统完全符合国家标准GB/61131... |
 |
M9811 直流电子负载 | M9811 is applicated in production line(cell charger, cell battery, electric vehicle battery, switching power supplier, linear power supplier, LED... |
 |
WT2080 LED驱动电源综合性能测试仪 | 产品简介： WT2080 LED驱动电源测试仪是一台能满足GB/T 24825-2009和IEC 62384:2006标准的LED驱动电源综合测试仪，能测试AC&DC输入输出特性，DC输出启动特性。 技术指标： 1） 输入特性测试（AC）：输入电压，电流，功率，功率因素，电网频率，总谐... |
 |
IS-*M**P 测光积分球 | IS-*M测光积分球，适用于节能灯、白炽灯、冷阴极灯、卤钨灯、直管形荧光灯、环形荧光灯、大功率直管形荧光灯、HID灯等光源光色电测试。 积分球尺寸可以根据顾客需求定制 直径：1.5m、1.75m、2.0m、2.5m、3.0m you may surf our website of our c... |
