ATE-2 LED Driver Automatic Test System
ATE-2 LED driver automatic test system is applied to the production line for the finished products testing. With features of simplified operation and nice-looking, the workers can operate it at very short time. This system can meet the requirements of IEC62384, GB24825-2009 and other relative standards.
Characteristics:
•This equipment adopts the special designed electronic load to imitate the V-I curve of LED.
•The normal LED driver has the disadvantage of high ripple, so it will have big deviation when it drives the traditional electronic load. For this equipment, the electronic load is update, so that to approach the real LED load.
•This system contains a programmable frequency conversion power supply to ensure fast switch and choose the input voltage and frequency of tested driver.
•The test equipments, electronic load and programmable frequency conversion power supply in this system are special developed and designed to meet the LED driver test requirements.
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection.
•It can test 4 LED drivers input and output at one time.
•The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer.
•Enable to print out the series number and parameters of sub-quality products by working with a micro-printer,
•Enable to achieve the barcode record function by working with a barcode scanner.
•The test report can be saved as Excel file for consult, statistic and analysis purpose.
•Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
System function:
•Low voltage test and surge current test:
Full-load test includes:
Input: Voltage, current, power, power factor, frequency, harmonic and 2 to 11 times harmonic component
Output: voltage, current, power, ripple wave, efficiency
Steady state test includes:
Steady state 1, steady state 2, steady state 3. The chopped wave of power (enable to test dimming lights), voltage, and frequency in each state can be set separately; the other parameters are same as the full-load test.
Linear adjustment rate test; load adjustment rate test
•Over output voltage (current) protection test, under output voltage (current) protection test
•Output shorten circuit protection test, output open circuit protection test
•Stabilization time test; cut off time test
•Capacity discharge function
•Barcode record function
Specifications:
| Item | Test Range | Tolerance | Test Condition |
| Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) |
45~65Hz sine-wave |
| DC: 3～500V | |||
| Current | AC: 5mA～2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Power Factor | 0.000～1.000 | ±(0.002+0.001/reading+1digit) | |
| Frequency | 45Hz～65Hz | ±0.1% Reading | |
| Harmonic | Total harmonic, and 2-11 times harmonic component | ±(0.1% range+5% Reading) | |
| Surge Current | 50mA～100A | ±(0.5% range+0.5% range+1digit) | Square wave with pulse width greater than 10 10μs Calibration validity: 12month |
| Lamp Voltage | AC: 3～300V (CF=1.67) | ±(0.1%reading+0.1%range+1digit) | 45~65Hz sine-wave Calibration validity: 12moths |
| DC: 3～500V | |||
| Lamp Current | AC: 5mA~2.7A (CF=3) | ||
| DC: 5mA～8A | |||
| Lamp Power | AC: 0.015～800W | ||
| DC: 0.015～4000W | |||
| Ripple Current | Max: 5mA～8A | ±(1%reading+1%range) | 20-70kHz sine-wave |
Note:
•Fundamental harmonic of voltage, current, lamp voltage, lamp current (AC) is 45Hz~65Hz. Frequency range is 45Hz~1MHz
•The frequency range of ripple current is 45Hz~1MHz.
you may surf our website of our company to get more information in here:
Send product request
Other supplier products
 |
LPCE-1 Spectrophotometer & Integrating Sphere Test System | LPCE-1 Integrating Sphere Spectrophotometer Test System is suitable for photometric and colorimetric measurement of luminaries such as Energy-savin... |
 |
M9811 DC Electronic Load | M9811 is applicated in production line(cell charger, cell battery, electric vehicle battery, switching power supplier, linear power supplier, LED... |
 |
LSG-2000 Goniophotometer with Rotating Mirror | LSG-2000 Goniophotometer with Rotating Mirror (Moving Mirror Goniophotometer) completely meet LM-79 Clause 9.3.1. The LSG-2000 is an automatic ligh... |
 |
CHROMA-2 Pocket Chroma Meter | Pocket Chroma Meter|Pocket Colorimeter is developed based on TOSHIBA TCD1304DG linear array CCD detector. It makes traditional laboratory instrumen... |
 |
WT2080 LED Power Driver Tester | WT2080 LED Power Driver Test Instrument is the comprehensive test instrument for LED drive power which is according to GB/T 24825-2009 and IEC 6238... |
Same products
 |
Winner802 Photon Correlation DLS Nano particle Size Analyzer | Seller: Jinan winner particle instrument stock Co.,Ltd. | Winner802 dynamic light scattering nanometerparticle size analyzer which based on the dynamic lig... |
 |
Winner-2008A Intelligent Laser Particle Size Analyzer | Seller: Jinan winner particle instrument stock Co.,Ltd. | Winner2008A full automatic wet laser particle size analyzeradopt MIE scattering principle,measure... |
 |
Winner 2000ZDE Intelligent Laser Particle Size Analyzer | Seller: Jinan winner particle instrument stock Co.,Ltd. | Winner2000ZDE intelligent laser particle size analyzer, perform auto test, auto alignment, auto w... |
 |
Winner 2018 Intelligent Laser Particle Size Analyzer | Seller: Jinan winner particle instrument stock Co.,Ltd. | Winner2018 Automatic laser particle size analyzer, perform auto test, auto alignment, auto water ... |
 |
Winner311XP Spray Laser Particle Size Analyzer | Seller: Jinan winner particle instrument stock Co.,Ltd. | Winner311XP desktop spray laser particle size analyzer is designed and developed specially for th... |
