LIFT, IMO Spread of Flame Apparatus
Get a quote：
Whats/App: +86 185 0176 3615
Web: qinsun-lab.com
Email: serving@qinsun-lab。com
This machineis designed according to ISO5658-2 standard D andproduction,while meeting the IMO FTP Code Resolution A. 653 (16) and ASTM E 1317 requirements. Lateral flame propagation properties for the determination of building products, flame propagationperformance / flamespread rate of speed can evaluate the fire retardant properties of the material.
The device via a gas radiant plate to heat samples and with heat flow meter to calibration; Test samples were placed in a vertical position, near the radiation plate, exposed in a clear area calibrated radiation flux. Close to the pilot flame test sample, but not in contact with the test sample, the sample was heated end ignited gas on the surface of the evaporator.
After ignition, recording the development of the flame front, and record the flame front in a horizontal direction to reach the surface of the sample,combustiondistance of each calibration elapsed time. Further testing materials include light heat, sustained combustion heat, critical flow, the average sustained burn calories, the total heat release and other relevant parameters.
Standards
• ISO 5658-2: reaction to fire test - Flame spread Part 2: Vertical distribution of building products side flame spread level.
• IMO FTP Code Resolution A. 653 (16): bulkhead, ceilinganddeck material flammability test procedures Advice
• ASTM E 1317: Marine Surface Finishes Standard Test Method for Flammability
ASTM E1321
Main Features
• The cabinet is made of stainless steel, corrosion-resistant and beautiful and easy to clean; The main framehavetwo separate parts of the burner frame and the specimen support framework. Two parts connected by bolts, and screws can beflexiblemechanical adjustment.
• Ignition sources: radiation plate and the United States imports a propane torch. Precise control of the flame height
• Burner, (200 ± 10) mm long holes ceramic tube,
• Cylinder type pilot burner flame support IMO standard automatic impact test; Optional
• Double grid and an enlarged perspective mirror observe the flamespread ,it is user-friendly
• Radiation plate temperature controller: prevent flames turned the heat radiating plate rear side;
• Flow controller can easily test content of methane in the test gas flame heat
• Gas supply: with a valve, zero-pressure valve, tempering valves, solenoid valves and a mixer, the mixed air and fuel gas supplied to the radiation plate.
• Providing a porous alignment plate and heat flow meter fixed on a sliding movement rail to detect heat flux if meet the standard requirements
• Equipped with an adjustable observation angle lens (750mm × 120mm), the test sample can rake through the glass mirror and observe the flame spread rate and by a foot switch,automaticrecord.
• Sample chimney equipped with compensating thermocouples.
• All radiant panel combustion control system safety explosion-proof, check valve, cut off the gas solenoid valve prevents the gas reflux
• The camera can observe a situation and save the test program (Optional)
• Measuring heat flow state within the range of the radiation plate for 50mm
• Data acquisition system can store the image length flame spread and combustion characteristics
• 19 "rack to measure the flame spread rate analysis, critical flow, heat release rate
• Radiation plate burner system is fully automated, with spark ignition and safetyprotectsystem;
•IMOprogram so that all calibration, test results print (IMO, ISO) easier (Optional)
Specification
| Model | STD-ISO5658-2 |
| Size | 1.710(W)×1.100(D)×1.985(H)mm |
| Console Size | 600(W)×750(D)×1.600(H)mm |
| Power | AC 220V, 50/60Hz, 30A |
| Weight | 200kg |
| Operating Manual | Supplied |
| Exhaust | Minimum 30m2/ min |
| Other requirements | Methane, PC, compressed gas, camcorders |
在线联系供应商
Other supplier products
 |
Xenon Arc Weather Ometer SI4000 | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Introduction： SI4000Xenon Arc Weather Ometer utilizes a xenon lamp to simulate id... |
 |
Enamel Boiling Water Resistance Tester ISO ASTM | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Enamel Boiling Water Resistance Tester is designed to evaluate the chemical at... |
 |
Filter Media Testing System | Standards ISO 11155-1 / DIN 71460-1 Technical Data Measurement range (dimensions) U-SMPS 2050: 10 – 800 nm Volume flow rate 0... |
 |
Bubble Pressure Method Membrane Pore Size Analyzer - lab instrument | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com Email: serving@qinsun-lab。com We are a professional testing instrument manufactur... |
 |
High and low temperature memory impact testing machine | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The High and Low Temperature Memory Impact Testing Machine is a computer-controlle... |
Same products
 |
Choosing the Right Equipment for Heavy-Duty Cleaning | 卖方: 868255 | FEIKE’s High Pressure Washer is designed for industrial cleaning, equipment maintenance, ve... |
 |
ER4043 Silicon Aluminum Welding Wire | 卖方: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin... |
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
