Functional Garment Pressure Testing Equipment
Whats/App: +86 156 1874 6768
Web: standard-groups.com
Applications
Full-Body Garment Stress Tester is used to evaluate the pressure exerted by various form-fitting garments or other wearable apparel on the human body. It quantifies the perceived pressure of clothing on the body into specific numerical data and enables assessment of test results. The manikin can perform both static and dynamic testing.
Dynamic postures meet the following requirements, considering the integrity of the form: the rear of the knees must not be left unprotected.
Standards
FZ/T 70015-2022 :Test Methods and Evaluation of Pressure in Knitted Compression Garments
Features
1.Accurate measurement of garment pressure at multiple body locations with high-resolution sensors.
2.Supports bothstaticanddynamic testing, simulating real-life movement and posture.
3.Pressure mapping allows objective evaluation of garment comfort and functionality.
4.Dynamic mannequin posture designed to maintain full body integrity, with clearance behind knees.
5.Enables design optimization for sports, medical, and fashion applications through data-driven analysis.
Parameters
| Item | Specifications |
|---|---|
| Pressure Mannequin | Average Asian female body type, height: 155 ~ 165 cm |
| Pressure Measurement Range | 0 ~ 90 mmHg |
| Test Accuracy | ≤0.1 mmHg |
| Resolution | ≤0.1 mmHg |
| Sensors | 26 independent sensors, each measuring a separate point. The sensor surface is flat and stable, with no mutual interference between measurement points. |
Accessories
1.Full-body mannequin (Asian female average build, height 155–165 cm)
2.26-point high-precision pressure sensor array
3.Data acquisition and analysis software
4.Adjustable fixtures for dynamic posture simulation
5.Calibration tools and reference pressure standards
Test Procedures
I. Equipment Preparation and Calibration
Parameter Verification: Ensure equipment complies with FZ/T70015-2022 standards. The pressure manikin uses the average Asian female physique (height 155–165 cm).
Sensor Inspection: All 26 sensors must have flat surfaces and stable configurations to ensure independent measurements without interference.
Range Calibration: Pressure measurement range 0–90 mmHg, test accuracy ≤0.1 mmHg, resolution ≤0.1 mmHg.
II. Test Procedure
1. Static Testing:
Place the garment over the pressure manikin and adjust to the standard posture (void space behind knees).
Activate the equipment, record pressure values at each point, and analyze pressure distribution uniformity.
2. Dynamic Testing:
Simulate movement postures (e.g., running, jumping) and observe pressure changes.
Focus on pressure values in high-activity areas (e.g., armpits, waist).
III. Data Interpretation and Optimization
1. Comfort Assessment:
Excessive pressure (>90 mmHg) may cause constriction, while insufficient pressure fails to provide adequate support.
Optimize pressure distribution by adjusting fabric elasticity or cutting techniques.
2. Function Verification:
Performance compression garments must deliver moderate pressure to key muscle groups (e.g., thighs, calves) to reduce muscle vibration.
Medical garments must ensure uniform pressure distribution to prevent blood circulation obstruction.
在线联系供应商
Other supplier products
 |
Resistance Tester for Molten Metal Droplet (Splash) Impact Performance | Whats/App: +86 156 1874 6768 Web: standard-groups.com Performance and Standards: This resistance tester for molten metal droplet (splash) impact... |
 |
Automotive Wire Hot Water（Salt Water）Resistance Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Automotive Wire Hot Water (Salt Water) Resistance Tester is engineered for long-term (o... |
 |
Dry Sand Rubber Wheel Wear Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of... |
 |
High Precision Fluoropolymer Cable Validation Tester Exporter | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Features (1) Precise force application using a servo-driven steel rod. (2) ... |
 |
ISO 5658 Flame Spread Index Tester | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com The Flame Spread Index Tester is designed to evaluate the flame propagation c... |
Same products
 |
ER4043 Silicon Aluminum Welding Wire | 卖方: 868776 | Hangzhou Kunli Welding Materials Co., Ltd. offers ER4043 Silicon Aluminum Welding Wire for alumin... |
 |
HDPE高速水冷双壁波纹管生产线 | 卖方: Shandong HUASU Plastic Technology Co.,Ltd. | 机头模具采用双流道结构、氮化磨光处理机头，偏壁调整方便快捷，保证内外层壁厚均匀和稳定成型。 最新设计密闭压力水冷冷却结构，冷却充分，多点分布真空系统，效率更高，生产速度更快。 双层在线扩口功... |
 |
PanEVAP & MVR system | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | A multiple-effect evaporator is a device that efficiently uses steam heat to evaporate water. Wat... |
 |
PanGAP wide gap welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanGAP wide gap welded plate heat exchangerconsists of a welded plate pack with different channel... |
 |
PanBloc welded plate heat exchanger | 卖方: Yangzhou Panstar Heat Exchanger Equipment Co., Ltd | PanBloc welded plate heat exchangeris compact and efficient, although fully welded, is totally ac... |
