Gas & Water Assisted Injection Mold
Gas & Water Assisted Injection Mold
Since the thermal conductivity and heat capacity of water are much bigger than nitrogen, so the injection cycle of water-assisted is about 70% shorter than the injection cycle of gas assisted injection molding; The product wall thickness of water-assisted injection molding is more even than gas-assisted; The inner wall roughness of water assisted injection moldingis smoother than that gas-assisted injection molding.
WATER & GAS ASSISTED INJECTION MOLDED PRODUCTS
TV Frame Mold
Pushing the liquid plastic into the cavity and core side by high pressure during the injection process, and the gas pressure is maintained to form a hollow section inside the thick wall of the plastic part, the injection process is called gas-assisted injection molding.
Bike Frame Mold for Kids
During plastic molding processing, gas-assisted injection molding is abbreviated as GAIM, which is a relatively new molding processing technology, this technology is comprehensively developed on the basis of the design and manufacture of traditional injection molding molds and blow molding molds, and entered the practical stage in the 1990s, gas-assisted injection molding has huge technical application advantages and can produce significant economic benefits.
Car Ceiling Handle Injection Mould
When plastic injection molding, the melt is under the injection pressure and enters the mold cavity, on the same section, the flow rate of each gate is different, the fastest in the middle, the closer to the cavity wall, the slower the flow rate, and it contacts the cavity wall, the speed of the first layer is zero.
Gas Assisted & Water Assisted Injection Molding Differences
- injection mold chinacost is much higher than that of gas injection mold.
Gas-Assisted Injection Molding Process
Gas-assisted injection molding is roughly divided into 4 stages: plastic injection, gas injection, pressure-holding cooling, and gas discharge.
Gas-assisted injection molding classification
- insert injection molding: under-material injection molding is also called short shot, inject part of the plastic melt (usually 50%-90% of the cavity volume) into the mold cavity first, and then inject gas to use push the melt to complete mold filling and pressure holding by gas, the gas injection time and gas pressure are very important to the product quality, to inject the gas too early or pressure is too high will cause the gas to penetrate the melt front, otherwise it will lead to incomplete feeding and surface defects. In this type of gas injection moulding process, when the gas pressure is too high and the gas is injected too early, gas penetration cannot be avoided, if the gas pressure is too low and the gas is injected too late, the gas will not enter the plastic and will not be able to promote the flow of the melt front. Increasing the initial air pressure can avoid stagnation of the forward melt, and there will be no traces on the surface of the product, the under-material injection process is suitable for the molding of rod-shaped products or plate-shaped products with partial walls thickness.
As one of gas injection moulding manufacturers, we will do our best to meet all the needs of customers.
在线联系供应商
Other supplier products
 |
Multi Cavity Mold | Multi Cavity Mold The runner filling balance must be considered when designing the multi-cavity mold in order to ensure the best effect of filling... |
 |
Plastic Pipe Mold | Plastic Pipe Mold The gas-assisted controller is used to control the pressure of nitrogen to the mold at different times, the controller is divi... |
 |
Medical TPE Mold | Medical TPE Mold Design is the source of a high-quality mold, one good mold design will be half success, USM uses the world's leading software to ... |
 |
32 Cavity Mold | 32 Cavity Mold In terms of multi-cavity molds, we pay attention to the design of layout and runner filling balance, which is also the key to the s... |
 |
8 Cavity Mold | 8 Cavity Silicone Mold USM as a medical plastic injection mouldingsupplier provides products including medical device plastic parts, suction tip... |
Same products
 |
steel moulds for precast concrete | 卖方: Sino Mould (Hubei) Co.,Ltd | steel moulds for precast concrete What Are Steel Moulds & Their Role for precast concre... |
 |
new jersey barrier moulds | 卖方: Sino Mould (Hubei) Co.,Ltd | new jersey barrier moulds Barrier Types & Custom Configurations Single-sided parapet bl... |
 |
culvert moulds | 卖方: Sino Mould (Hubei) Co.,Ltd | culvert moulds Structural & Configuration Types By Mold Configuration: Horizontal-type ... |
 |
manhole forming systems | 卖方: Sino Mould (Hubei) Co.,Ltd | manhole forming systems Precast Manhole/ Inlet Molds , Also called Molds for Inspection Cha... |
 |
precast concrete molds | 卖方: Sino Mould (Hubei) Co.,Ltd | precast concrete molds About Sino Mould Sino Mould is a precast concrete mould manufacturer... |
