Sulfur content analyzer in petrol products (X-ray spectroscopy methods)
Scope of application
Sulfur content of petroleum products tester (X-ray spectroscopy) People's Republic of China in accordance with requirements of the standard GB/T11140, GB/T17040, ASTM D4294 specified in the design and manufacture of this instrument for the determination of trace sulfur content in petroleum products. Because it uses physical analysis methods, analytical speed, without complicated sample preparation, high precision, human error, low labor intensity, no pollution, it has been widely applied and basic replace other measuring sulfur in the international arena methods of analysis.
Function characteristics
1, English operating system, man-machine interface of friendly exchanges. 2, detection time is short, the automatic test results within 30 seconds; automatic C / H ratio correction for multiple samples; 3, large-screen LCD display, automatic print measurement data; 4, using the X-ray tube excitation, the instrument can be used for a long while without source attenuation effects; 5, use of physical methods of analysis, the analysis does not contact does not destroy the sample, without chemical reagents; 6, instrument with integrated design, easy maintenance;
Technical parameters
1, The scope of analysis: S analytical range can be adjusted by calibration curve method selected.
2, The width of the scope of analysis: S max-S%% min9.999%; such as oil: S: 0.001 to 9.999%
3, The inherent error, the accuracy of analysis: such as oil: in line with The national standard GB / T 17040, also comply with The relevant requirements of The American National Standards ASTM D4294.
4, System analysis time: 1 ~ 999 seconds, The recommended value is 60 seconds.
5, The detection limit: 10ppm
6, The conditions: Ambient temperature: 5 to +40 ° C, Relative humidity:85% (30 ° C) Power supply: 220V ± 20V, 50Hz.
7, Total power consumption: <150W.”
在线联系供应商
Other supplier products
 |
Rapid low temperature Closed Cup Flash Point tester | Scope of application Function characteristics 1, A color display allow for user friendly interface. 2, Model FDT-023 prompt function automatically... |
 |
Sulfur content analyzer (lamp methods) | Scope of application Sulfur Content Analyzer(Lamp Method) is designed and madeas perthe National Standard of People’ Republic of China GB/T38... |
 |
Octane number analyzer (motor / research method) | Gasoline octane (gasoline label) is used to indicate a contract value of gasoline antiknock properties of motor gasoline the most important indicat... |
 |
Automatic closed cup flash point tester of petroleum products | Scope of application Applied standards: GB/T 261-2008, ASTM D93-02 Application range: applies to the determination of flash point of petroleum prod... |
 |
Automatic Cleveland Open Cup Flash Point Tester | Scope of application For flash and Fire points of all petroleum products, except fuel oils and those having an open cup flash below 79° C (175&... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
