Salt Spray Test Chamber

Salt Spray Test Chamber | Salt Fog Test | ASTM B117 Salt Spray ChamberSalt Spray Test Chamberis applicable to the salt spray corrosive test for the protection layer of components, parts, electronic and electrical parts and metal materials and industrial products. The salt fog test chamber meets the following standards:IECGB/T2423.17),GB/T10125, GB/T1771,ISO9227,ASTM-B117, GB/T2423-18,QBT3826,QBT3827, IEC 60068-2-52, ASTM-B368, MIL-STD-202, EIA-364-26, GJB150, DIN50021-75, ISO3768, 3769, 3770; CNS 3627, 3885, 4159, 7669 etc.

Specifications:
• A waterproof structure is adopted between the chamber cover and chamber body, thus there is no salt spray overflow.
• Adopts the tower spraying system and equipped with the salt solution filter system and non-crystal nozzle so as to realize even salt spray distribution and freely adjustable settlement.
• TheSalt Spray ChamberWorking room temperature range:RT+5ºC~50ºC (The setting value cannot be lower than the current ambient temperature); Saturated barrel temperature: +40°C~+63°C;
• Brine temperature: preheated by laboratory temperature; Temperature uniformity: ≤ ±2°C; Temperature fluctuation: ≤ ±1°C;
• The Salt Spray Test time: 0-99,999m (adjustable); Settlement: 1-2ml/80cm²/h;
• The Salt Spray Test Chamber Spray method: NSS (neutral) test, AASS (acidic) test, CASS (copper acceleration) test, custom test, programmable test, each test can choose continuous spray or intermittent spray (according to industry standards). The ratio of each test solution has a corresponding explanation in the test setting interface.
• Sample holder: at an angle of 15 to 30 degrees from the vertical surface (with sample standard placed). Other irregular samples are recommended to remain tilted. The V-groove has a single weighing capacity of 3KG, and the O-bar has a single bearing capacity of 5KG. It is strictly forbidden to place samples under heavy weight.

How do you do a salt spray test?

1. First power on thesalt spray test chamber(plug in)
2. Press the red power switch panel from left to right, respectively: the low water level A light is on, the low salt water B light is on, and the low water level C light is on.
3. Pour distilled water directly into the test chamber, wait until the water level A indicator light off, and stop adding water. […more…]

How Long does a Salt Spray Test Take?

The Salt Spray Test Chamber is an environmental test equipment that evaluates the corrosion resistance of products or metal materials by artificially simulating salt spray environmental conditions. The chloride concentration in the salt spray environment can be several or tens of times the salt spray content of the general natural environment, which greatly increases the corrosion rate. Thesalt spray testingof the product can greatly shorten the time to obtain the result. For example, if a product is tested in a natural exposure environment, it may take 1 year for its corrosion, while a test in salt spray test chamber may take as long as 24 hours to obtain similar results.

How to use a salt spray test chamber to determine the corrosion resistance of LED lamps?

Salt spray test is a kind of environmental reliability test, mainly used to test the corrosion resistance of metal materials of lamps. In order to verify whether the metal parts on the product will corrode when exposed to the atmosphere or other environments, the product can be placed in the use environment for a long enough time, such as a product life cycle. This is time-consuming and labor-intensive. In practice, it is rarely used, so a convenient method is needed to evaluate the corrosion resistance of the product.

Other supplier products

	Portable CCD LED Colorimeter Spectroradiometer	The Portable CCD LED Colorimeter Spectroradiometer has the following versions which can measure different parameters: LISUN Model Functio...
	Dustproof Testing Machine for IP5X and IP6X	Product Description SC-015Dust-proof Test Chamber(Sand Dust Chamber) is applied to physical and other related performance tests for electronic...
	Electrostatic Discharge Simulator	Product Description ESD simulator guns(Electrostatic Discharge Generator/Electrostatic Gun/ESD Guns) is in full compliance withIEC 61000-4-2,E...
	Automatic Electrical Safety Tester	Product Description The LS9955/LS9956Automatic Safety Test System(electrical safety analyzer) combined the following function in one set: With...
	LED Power Driver Tester	Product Description LS2090 LED Power Driver Test Instrument is the comprehensive test instrument for LED driver power which is according toGB/...

供应产品

Same products

	MECHANIC MEC 4K 2K 高清电子目镜相机，适用于立体显微镜	卖方: 深圳市维客修科技有限公司	描述 美卡尼克MEC 2K/2K PRO/4K高清电子目镜摄像机，可以将双目立体显微镜改装成三目显微镜。采用SONY 1/2.3"进口CMOS传感器，采用优质CMOS传感器，硬...
	Fluke 15B+ 17B+ 18B+ 数字万用表电压频率测试仪	卖方: 深圳市维客修科技有限公司	iFixes 10CC半透明/全透明/乳白色/浅无铅助焊膏适用于手机主板CPU BGA维修。iFixes助焊剂注射器注射焊膏焊接膏手机整理焊接耗材系列，适用于电路板纳米芯片，手机PCB， SMT...
	HTT-02 Hot Tack Tester	卖方: Cell Instruments Co., Ltd	The HTT-02 Hot Tack Testeris specifically designed to assess this property by measuring the stren...
	SPC-01 Stretch Film Peeling Cling Tester	卖方: Cell Instruments Co., Ltd	The SPC-01 Stretch Film Peeling Cling Testermeasures the adhesion between two layers of stretch f...
	FTT-01 Film Thickness Tester	卖方: Cell Instruments Co., Ltd	The FTT-01 FilmThickness Testerutilizes a mechanical scanning technique to measure the thickness ...