Salt Spray Test Chamber

• 

Salt Spray Test Chamber | Salt Fog Test | ASTM B117 Salt Spray ChamberSalt Spray Test Chamberis applicable to the salt spray corrosive test for the protection layer of components, parts, electronic and electrical parts and metal materials and industrial products. The salt fog test chamber meets the following standards:IECGB/T2423.17),GB/T10125, GB/T1771,ISO9227,ASTM-B117, GB/T2423-18,QBT3826,QBT3827, IEC 60068-2-52, ASTM-B368, MIL-STD-202, EIA-364-26, GJB150, DIN50021-75, ISO3768, 3769, 3770; CNS 3627, 3885, 4159, 7669 etc.

Specifications:
• A waterproof structure is adopted between the chamber cover and chamber body, thus there is no salt spray overflow.
• Adopts the tower spraying system and equipped with the salt solution filter system and non-crystal nozzle so as to realize even salt spray distribution and freely adjustable settlement.
• TheSalt Spray ChamberWorking room temperature range:RT+5ºC~50ºC (The setting value cannot be lower than the current ambient temperature); Saturated barrel temperature: +40°C~+63°C;
• Brine temperature: preheated by laboratory temperature; Temperature uniformity: ≤ ±2°C; Temperature fluctuation: ≤ ±1°C;
• The Salt Spray Test time: 0-99,999m (adjustable); Settlement: 1-2ml/80cm²/h;
• The Salt Spray Test Chamber Spray method: NSS (neutral) test, AASS (acidic) test, CASS (copper acceleration) test, custom test, programmable test, each test can choose continuous spray or intermittent spray (according to industry standards). The ratio of each test solution has a corresponding explanation in the test setting interface.
• Sample holder: at an angle of 15 to 30 degrees from the vertical surface (with sample standard placed). Other irregular samples are recommended to remain tilted. The V-groove has a single weighing capacity of 3KG, and the O-bar has a single bearing capacity of 5KG. It is strictly forbidden to place samples under heavy weight.

How do you do a salt spray test?

1. First power on thesalt spray test chamber(plug in)
2. Press the red power switch panel from left to right, respectively: the low water level A light is on, the low salt water B light is on, and the low water level C light is on.
3. Pour distilled water directly into the test chamber, wait until the water level A indicator light off, and stop adding water. […more…]

How Long does a Salt Spray Test Take?

The Salt Spray Test Chamber is an environmental test equipment that evaluates the corrosion resistance of products or metal materials by artificially simulating salt spray environmental conditions. The chloride concentration in the salt spray environment can be several or tens of times the salt spray content of the general natural environment, which greatly increases the corrosion rate. Thesalt spray testingof the product can greatly shorten the time to obtain the result. For example, if a product is tested in a natural exposure environment, it may take 1 year for its corrosion, while a test in salt spray test chamber may take as long as 24 hours to obtain similar results.

How to use a salt spray test chamber to determine the corrosion resistance of LED lamps?

Salt spray test is a kind of environmental reliability test, mainly used to test the corrosion resistance of metal materials of lamps. In order to verify whether the metal parts on the product will corrode when exposed to the atmosphere or other environments, the product can be placed in the use environment for a long enough time, such as a product life cycle. This is time-consuming and labor-intensive. In practice, it is rarely used, so a convenient method is needed to evaluate the corrosion resistance of the product.

Other supplier products

	CCD Spectroradiometer Integrating Sphere Compact System	LPCE-3 is a CCD Spectroradiometer Integrating Sphere Compact System for LED Testing. It is suitable for single LED and LED luminaires' photometric,...
	Electrostatic Discharge Simulator	Product Description ESD simulator guns(Electrostatic Discharge Generator/Electrostatic Gun/ESD Guns) is in full compliance withIEC 61000-4-2,E...
	LM-79 Moving Detector Type C Goniophotometer	LSG-6000 Moving DetectorGoniophotometer(Mirror Type C) was manufactured by LISUN completely meetsLM-79-19,IES LM-80-08,COMMISSION DELEGATED REGULAT...
	High Voltage Lightning Surge Generator	Basic Info. Model NO. SG-61000-5 After-sales Service Perfect Warranty 24months Trademark LISUN Origin China ...
	High Precision Spectroradiometer Integrating Sphere System	Basic Info. Model NO. LPCE-2 After-sales Service Perfect Warranty 24months Trademark LISUN Origin China ...

Same products

	Disposable Dental Needles	Seller: Shanghai Kohope Medical Devices Co., Ltd.	The dental needles manufacturing, also named disposable dental needles and tooth needles, are ass...
	ULTRASONIC STEEL PIPE TESTING EQUIPMENT	Seller: Hebei tianxianghao metallurgical equipment manufacturing co.,ltd	Ultrasonic pipe testingwith ultrasonic pipe inspection equipmentrefers to a non-destructive testi...
	STEEL PIPE STORAGE RACK	Seller: Hebei tianxianghao metallurgical equipment manufacturing co.,ltd	Metal Pipe Storage Racks This ms pipe storage rackmachine serves as a storage system for inspect...
	STEEL PIPE ROTATING ROLLER TABLE	Seller: Hebei tianxianghao metallurgical equipment manufacturing co.,ltd	This equipment is suitable for the detection and repair welding process in the production of spir...
	STEEL PIPE END EXPANDING MACHINE	Seller: Hebei tianxianghao metallurgical equipment manufacturing co.,ltd	Pipe expanding machineis a professional equipment for expanding and rounding the end of spiral su...