Safety Testing Equipment for Explosive Limits/ Explosion Boundary Tester/ High-Temperature High-Pressure Explosion Tester
Reference Standards:
EN 1839 ASTM E918 ASTM E2079 EN 15967 UL9540A
Product Features:
1. Designed with a modular concept to flexibly meet various testing requirements.
2. Allows for free editing of the experimental process to cater to different testing needs.
3. The testing container is made of 316L stainless - steel, which is corrosion - resistant.
4. It adopts a jacket temperature - control method, featuring high temperature - control efficiency.
5. The constant - temperature conditions can be flexibly set, balancing efficiency and accuracy.
6. Equipped with a high - efficiency vacuum pump, and the cleaning parameters can be set to fully eliminate residual effects.
7. With a precision measurement and control system and a compensation gas - mixing algorithm, it enables precise control of gas concentration.
8. It has a stirring function to ensure the uniformity of the mixed gas.
9. It uses a pressure sensor specially designed for explosions, which can work at high temperatures and has good dynamic performance. 10. Automatic control of gas samples, including automatic vacuum - pumping, automatic gas - mixing, and automatic stirring.
11. The equipment has a safety interlock function to enhance safety.
12. Multiple safety protections such as safety valves and burst discs effectively ensure the safety of experimenters.
Technical parameters:
|
Operating Environment |
(-5 to 45)°C, <95%RH |
|
Test Vessel Temperature Control Range |
Room temperature to 200°C |
|
Configuration Gas Maximum Pressure |
Supports one atmosphere, ±0.1%FS |
|
Test Vessel Design Pressure |
≥2.0MPa |
|
Explosive Pressure Sensor |
≥5.0MPa, linear ±1.0%FS |
|
Explosive Pressure Acquisition System Sampling Frequency |
≥5kHz |
|
Explosive Pressure Acquisition System Single Experiment Data |
≥10,000 cycles |
|
Gas Input Channel |
3 channels |
|
Maximum Stirrer Speed |
400rpm, speed adjustable |
在线联系供应商
Other supplier products
 |
Differential Scanning Calorimetry Tester | Scope of application: It is used to analyze the thermal effect and corresponding temperature when the physical or chemical properties of organic a... |
 |
Helmets Vertical SpacingInfrared - positioning Tester/ safety helmet vertical spacing tester / helmet fit measurement device | Purpose This measuring instrument is used to measure the vertical spacing and wearing height of safety helmets. Applicable Standard GB/T 2812-... |
 |
Roughness profiler | Product Introduction: The profiler is measured by the slip of the stylus of the instrument and the surface to be measured, and is a contact measur... |
 |
Rupture strength tester | Standard IEC 61730-2: Photovoltaic (PV) Module Safety Qualification – Requirements for Testing UL 61730: Safety Standard for Photovoltaic... |
 |
Face Mask Filtration Efficiency Tester | Meet the standard: ASTM F2100 ASTM F2299 EN 149 NIOSH 42 CFR Part 84 ISO 16900-3 YY 0469 YY/T 0617 Product Introduction: The primary function... |
Same products
 |
Air Permeability Tester STD- F8 | 卖方: Standard International Group (HK) Limited | The Air Permeability Tester is designed to quickly and accurately measure the breathability and p... |
 |
Surface Performance Tester STD-FB4 - A | 卖方: Standard International Group (HK) Limited | Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti... |
 |
Compression Tester STD - FB3 - A | 卖方: Standard International Group (HK) Limited | TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar... |
 |
Single - Strand Bending Tester STD - FB2 - SH | 卖方: Standard International Group (HK) Limited | Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ... |
 |
Bending Tester STD- FB2 - S | 卖方: Standard International Group (HK) Limited | Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig... |
