Thermal cycle wet freezing testing machine
The Thermal Cycle Wet Freezing Testing Machine is designed for comprehensive environmental testing, capable of simulating extreme temperature and humidity conditions. It provides precise control and high repeatability for accelerated aging, condensation resistance, and reliability testing of batteries, photovoltaic modules, and electronic components. Its dual-chamber design ensures simultaneous wet and dry testing, enabling efficient evaluation under multi-environment conditions.
Application
(1) Environmental performance testing of lithium-ion batteries and battery modules
(2) Design qualification and type approval testing for photovoltaic (PV) modules
(3) Reliability and durability testing of electronic control units (ECUs) and PCBA
(4) Research and development for automotive and renewable energy components
Standards
(1) IEC 61215 – Terrestrial Photovoltaic (PV) Modules: Design Qualification and Type Approval
(2) UL 1073 – Safety of Enclosures for Electrical Equipment
(3) ISO 16750-4 – Road Vehicles: Environmental Conditions and Testing for Electrical and Electronic Equipment
(4) CE Certification – Conformité Européenne
(5) RoHS Compliance – Restriction of Hazardous Substances
(6) Optional: IEC 60068 series for environmental testing of electronic equipment
Features
Extreme Environmental Simulation: -40°C to +85°C operational range; 98% RH humidity control.
Ultra-Stable Performance: ±1°C temperature stability and ≤±2°C uniformity across chamber.
Rapid Transient Response: 10°C/min heating and 7°C/min cooling with auto-tuning PID.
Energy Efficiency: Advanced insulation and heat recovery for 40% lower power consumption; ECO mode for idle periods.
Safety Features: Dual overload protection, thermal cutout, current-limiting breaker, and door interlock.
User-Friendly Interface: 10” touchscreen HMI with preloaded test profiles and customizable hold times.
Remote Monitoring: Wi-Fi/Ethernet connectivity with real-time alerts via SMS or .
Glovebox Compatibility: Controlled oxygen and moisture levels for sensitive component testing.
Parameters
| Parameter | Specification |
|---|---|
| Temperature Range | -40°C to +85°C (operational) |
| Temperature Fluctuation | ≤ ±1°C |
| Temperature Deviation | ≤ ±1°C (steady state) |
| Temperature Uniformity | ≤ ±2°C (empty chamber) |
| Heating Rate | 10°C/min (typical, configurable) |
| Cooling Rate | 7°C/min (typical, configurable) |
| Humidity Range | 30%–98% RH (non-condensing) |
| Humidity Deviation | ±3% FS (at 85% RH ±2%, 90% RH ±2%) |
| Chamber Volume | 500 L (standard), expandable to 1,500 L |
| Power Supply | 380V/415V, 3-phase, 50/60Hz |
| Dimensions (W×D×H) | 1,200 mm × 1,800 mm × 2,000 mm |
| Weight | 800 kg (net) / 1,200 kg (gross) |
Accessories
(1) Universal sample racks (4 pcs, adjustable for batteries, PV modules, or PCBAs)
(2) Humidity sensor calibration capsules (10 pcs)
(3) Software Suite: EnviroTest Pro license for Windows/Linux, including 1-year cloud test report access
(4) Calibration and Safety: NIST-traceable temperature/humidity logger, emergency portable eyewash station
(5) Maintenance Kit: Spare heating elements, refrigerant filters, chamber cleaning solution (non-corrosive)
(6) Documentation: Multilingual quick-start guide, compliance certificates for IEC/UL/ISO standards
Test Procedures
Install test samples in universal sample racks and close chamber doors securely.
Set test parameters on the touchscreen HMI or select a preloaded IEC/UL test profile.
Adjust target temperature, humidity, heating/cooling rate, and test duration as required.
Start the test sequence; system performs automated ramping and environmental cycling.
Monitor real-time conditions via touchscreen or remote connectivity.
At completion, allow chamber to return to ambient temperature before retrieving samples.
Export test reports via software interface for analysis.
Maintenance Information
Regularly inspect and clean chamber surfaces to avoid residue accumulation.
Replace HEPA filters, heating elements, and refrigerant filters as recommended by the manufacturer.
Perform NIST-traceable calibration of temperature and humidity sensors annually.
Verify door interlocks and emergency shutdown circuits before each test series.
Store the unit in a dry, ventilated environment when not in use.
在线联系供应商
Other supplier products
 |
Glass Bottle Internal Pressure Resistance Tester | The internal pressure resistance tester for glass bottles is a device specifically used to test the internal pressure - resistance performance of g... |
 |
Coatings Shear | Standard YY/T 0856-2011 (China): Specifies mechanical testing protocols for metal angular fixators, including single-compression bending and bendi... |
 |
Cut Susceptibility Tester | Standard IEC 61730-2: Photovoltaic (PV) Module Safety Qualification – Requirements for Testing UL 1703: Flat-Plate Photovoltaic Modules and... |
 |
Metal Bone Screws Torque Tester | Standard YY/T 1506. ASTM F543: The standard specifies the torque required to measure the torque required to screw a metallic bone grafting screw ... |
 |
Sliding Bearing Fatigue Testing Machine | The sliding bearing fatigue testing machine is an important testing device, mainly used to evaluate the fatigue life and performance of sliding bea... |
Same products
 |
Full-Body Garment Stress Tester,FZ/T 70015 | 卖方: Standard International Group (HK) Limited | TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe... |
 |
Industrial Dry Cleaning Machine,industrial garment steamer | 卖方: Standard International Group (HK) Limited | TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel... |
 |
MST Medical Compression Stocking Tester,compression sock tester | 卖方: Standard International Group (HK) Limited | The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the... |
 |
MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool | 卖方: Standard International Group (HK) Limited | Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi... |
 |
Dental material color stability tester | 卖方: Standard International Group (HK) Limited | Application The applications of color stability testers for dental materials are mainly reflecte... |
