Thermal cycle wet freezing testing machine

The Thermal Cycle Wet Freezing Testing Machine is designed for comprehensive environmental testing, capable of simulating extreme temperature and humidity conditions. It provides precise control and high repeatability for accelerated aging, condensation resistance, and reliability testing of batteries, photovoltaic modules, and electronic components. Its dual-chamber design ensures simultaneous wet and dry testing, enabling efficient evaluation under multi-environment conditions.

Application

(1) Environmental performance testing of lithium-ion batteries and battery modules

(2) Design qualification and type approval testing for photovoltaic (PV) modules

(3) Reliability and durability testing of electronic control units (ECUs) and PCBA

(4) Research and development for automotive and renewable energy components

Standards

(1) IEC 61215 – Terrestrial Photovoltaic (PV) Modules: Design Qualification and Type Approval

(2) UL 1073 – Safety of Enclosures for Electrical Equipment

(3) ISO 16750-4 – Road Vehicles: Environmental Conditions and Testing for Electrical and Electronic Equipment

(4) CE Certification – Conformité Européenne

(5) RoHS Compliance – Restriction of Hazardous Substances

(6) Optional: IEC 60068 series for environmental testing of electronic equipment

Features

Extreme Environmental Simulation: -40°C to +85°C operational range; 98% RH humidity control.

Ultra-Stable Performance: ±1°C temperature stability and ≤±2°C uniformity across chamber.

Rapid Transient Response: 10°C/min heating and 7°C/min cooling with auto-tuning PID.

Energy Efficiency: Advanced insulation and heat recovery for 40% lower power consumption; ECO mode for idle periods.

Safety Features: Dual overload protection, thermal cutout, current-limiting breaker, and door interlock.

User-Friendly Interface: 10” touchscreen HMI with preloaded test profiles and customizable hold times.

Remote Monitoring: Wi-Fi/Ethernet connectivity with real-time alerts via SMS or .

Glovebox Compatibility: Controlled oxygen and moisture levels for sensitive component testing.

Parameters

Parameter	Specification
Temperature Range	-40°C to +85°C (operational)
Temperature Fluctuation	≤ ±1°C
Temperature Deviation	≤ ±1°C (steady state)
Temperature Uniformity	≤ ±2°C (empty chamber)
Heating Rate	10°C/min (typical, configurable)
Cooling Rate	7°C/min (typical, configurable)
Humidity Range	30%–98% RH (non-condensing)
Humidity Deviation	±3% FS (at 85% RH ±2%, 90% RH ±2%)
Chamber Volume	500 L (standard), expandable to 1,500 L
Power Supply	380V/415V, 3-phase, 50/60Hz
Dimensions (W×D×H)	1,200 mm × 1,800 mm × 2,000 mm
Weight	800 kg (net) / 1,200 kg (gross)

Accessories

(1) Universal sample racks (4 pcs, adjustable for batteries, PV modules, or PCBAs)

(2) Humidity sensor calibration capsules (10 pcs)

(3) Software Suite: EnviroTest Pro license for Windows/Linux, including 1-year cloud test report access

(4) Calibration and Safety: NIST-traceable temperature/humidity logger, emergency portable eyewash station

(5) Maintenance Kit: Spare heating elements, refrigerant filters, chamber cleaning solution (non-corrosive)

(6) Documentation: Multilingual quick-start guide, compliance certificates for IEC/UL/ISO standards

Test Procedures

Install test samples in universal sample racks and close chamber doors securely.

Set test parameters on the touchscreen HMI or select a preloaded IEC/UL test profile.

Adjust target temperature, humidity, heating/cooling rate, and test duration as required.

Start the test sequence; system performs automated ramping and environmental cycling.

Monitor real-time conditions via touchscreen or remote connectivity.

At completion, allow chamber to return to ambient temperature before retrieving samples.

Export test reports via software interface for analysis.

Maintenance Information

Regularly inspect and clean chamber surfaces to avoid residue accumulation.

Replace HEPA filters, heating elements, and refrigerant filters as recommended by the manufacturer.

Perform NIST-traceable calibration of temperature and humidity sensors annually.

Verify door interlocks and emergency shutdown circuits before each test series.

Store the unit in a dry, ventilated environment when not in use.

Other supplier products

	Ink printing durability test device	Product Usage: Printing ink Decolorization test machine, also known as abrasion tester, friction tester, etc., mainly for printing ink for printed...
	Protective Clothing Flame Spread Test Machine	The tester is used for flame spread test of protective clothing. It is designed and manufactured according to ISO 15025 Standard for Protective Clo...
	Powder Wet Vibrating Screen System For Lithium Battery Material Testing	The Powder Wet Vibrating Screen System is designed for particle size separation and distribution analysis of lithium battery materials under wet co...
	Computer-controlled Helmet Impact Tester	Application Scope This testing instrument is applicable to the impact - energy absorption performance test of helmets. It is used to evaluate the ...
	Demesia Zigzag Tester	The Demesia Zigzag Tester is a professional device used to test the flexural resistance of materials such as rubber, leather, synthetic leather, an...

All supplier products

Same products

	Air Permeability Tester STD- F8	Seller: Standard International Group (HK) Limited	The Air Permeability Tester is designed to quickly and accurately measure the breathability and p...
	Surface Performance Tester STD-FB4 - A	Seller: Standard International Group (HK) Limited	Introduction TheSurface Tester analyzes finger movements-particularly, strokes-performed by arti...
	Compression Tester STD - FB3 - A	Seller: Standard International Group (HK) Limited	TheCompression Tester analyzes hand movements-particularly, pushing with a finger-performed by ar...
	Single - Strand Bending Tester STD - FB2 - SH	Seller: Standard International Group (HK) Limited	Standards ASTM A370. ASTM A416. ISO6934.4 The Single Fiber Bending Tester makes it possible to ...
	Bending Tester STD- FB2 - S	Seller: Standard International Group (HK) Limited	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rig...