Wire Fire Resistance+ Mechanical Shock Testing Machine，IEC 60331

Wires and cables that are hard to catch on fire and have the ability to prevent or delay the spread of fire are usually referred to the wires and cables that can be tested by IEC60332-3.Thistester is degsigned and produced accordance with the BS6387-2013 and GB/T 19216 to the latest standards requirements. Because two kinds of tests can be carried out on the one electrical control box, this tester could savings much cost for customers.

All kinds of experiments can be freely selected on the touch screen.

Standards:

• IEC 60331 part 12

• IEC 60331 part 31• IEC 60331-1

• (Option)BS6378:2013 Performance requirements for cables required to maintain circuit integrity under fire conditions

Main Features:

1. The burner is a belt type propane blowtorch with a Venturi mixer, and the burner nozzle is length 500mm, width 15mm.

2. Those burning holes are staggered into 3 rows, and the front width is 15mm, holes diameter is 1.32mm and these holes center distance is 3.2mm;

3. Double flow meter and pressure regulator at the inlet.

4. Air flow is (80± 5) L/min,and Propane flow is (5 ±0.25) L/min;

5. Diameter of the K-type thermocouple is 2mm,

6. One end of the specimen holder is equipped with a clamp to fix the sample, and the other end is convenient for heat transfer along the longitudinal specimen;

7. An inner diameter of the sample supporting metal rings is 150mm, and the cross-sectional diameter of the ring is 10 ± 2mm.

8. Equipped with two 1.5mm thermocouple; horizontal 45mm far away from the burner;Flame temperature is 750+50 °C; according to BS6387 standard temperature 950 ºC;

9. Control system is designed with Intelligent detection, during the test when short circuit occurs, automatic alarm and turn off the ignition.

10. PLC and touch screen control system, and automatically record store test data.

11. The circuit current fuse is 2A;

12. Samples impose power AV 100V~1000V adjustable;

13. The test time can be set freely, the standard recommending time is 90min,

14. 27m ³ combustor is optional.

Fire Resistance：

1. The burner nozzle length 500mm, width 15mm, there are three holes on the nozzle opening troubleshooting, pore radius of 1.32 mm pitch is 3.2 mm. Equipped with Venturi mixer;

2. Installation and testing of the cable ladder fastened to the supporting steel chassis; the testing process can be adjusted on both sides of the vertical component testing ladder depending on cable size requirements (test stand length: 1200mm, height: 60mm, total weight: 18 ± 1kg)

Metal ring inside diameter of about: 150 mm.

3. With a temperature measuring device (diameter less than 2mm K-type thermocouple, from the flame ports 75mm).

The front burner torch from the bottom of the box less than 200MM, 500MM and from the tank wall at least

According to the test grade, the flame temperature is adjustable: 600 ~ 1000 ° (A grade 650 °, B grade 750 °, C, D grade 950 °)

4. The horizontal distance between the center of the burner test cable 40-60MM, the vertical axis from the longitudinal axis of the specimen cable burner 100-120MM

5. Provide standards of five inner diameter of about 150 mm from metal rings, metal ring distance can be freely adjusted to facilitate sample fixed hold.

6. Stainless steel sample tray, load 30kg

Impact test :

1. Stainless steel impact structure;

2. Impact cone is a round steel bar diameter of 25mm and length 600mm.

3. Impact cone at 60-degree angles free fall,

4. Motor-driven rods hammer shock action cycling.

5. Impact cycles is 30±2Sper time

6. Ribbon burners ( the same one with spray test) (used with fire-resistant combustion tester)

7. Test temperature 600~1000 ° (a grade 650 °, b grade 750 ° and c,d 950 ° )

8. The diameter of K-type thermocouple is 2mm.

9. The circuit current of each phase is 0.25A.

Specification:

Model	STD-IEC60331B
Size	1.600(W)×850(D)×1.650(H)mm
Control table	600(W)×750(D)×1.200(H)mm
Power	AC 380V 3-phase, 50/60Hz, 30A
Weight	300kg
Exhaust	Min 15M2/Min

Other supplier products

	Digital display electronic ink viscosity meter	How it works: The working principle of the digital display electronic ink viscosity meter is based on two tin (usually a metal roller and a rubber...
	Torque - to - Failure Tester for Metal Bone - connecting Screws	Standard YY/T 0662-2008(Chinese standard for orthopedic implant testing) ISO 5832-1(Metallic materials for surgical implants – Wrought stai...
	Film Heat Shrinkage Tester	The film heat shrinkage rate tester is a device specifically designed to measure the shrinkage performance of film materials under heating conditio...
	Carbon Black Content meter	Standard GB 13021-1991: Determination of carbon black content in polyethylene compounds. GB/T 2951.41-2008: Test method for carbon black and ash ...
	HEPA/ULPA filter scanning test bench	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application (1) HEPA and ULPA Filter Classification: Determine filter grade and performanc...

供应产品

Same products

	Full-Body Garment Stress Tester,FZ/T 70015	卖方: Standard International Group (HK) Limited	TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe...
	Industrial Dry Cleaning Machine,industrial garment steamer	卖方: Standard International Group (HK) Limited	TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel...
	MST Medical Compression Stocking Tester,compression sock tester	卖方: Standard International Group (HK) Limited	The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the...
	MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool	卖方: Standard International Group (HK) Limited	Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi...
	Dental material color stability tester	卖方: Standard International Group (HK) Limited	Application The applications of color stability testers for dental materials are mainly reflecte...