Full-Body Garment Stress Tester,FZ/T 70015

TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exerted by tight-fitting garments or wearable apparel on the human body. You can use it to convert the tactile perception of garment pressure into measurable data, enabling accurate evaluation of comfort, support, and functionality. The device supports both static and dynamic testing on a mannequin, providing comprehensive pressure mapping for design optimization and performance verification.

Applications

Full-Body Garment Stress Tester is used to evaluate the pressure exerted by various form-fitting garments or other wearable apparel on the human body. It quantifies the perceived pressure of clothing on the body into specific numerical data and enables assessment of test results. The manikin can perform both static and dynamic testing.

Dynamic postures meet the following requirements, considering the integrity of the form: the rear of the knees must not be left unprotected.

Standards

FZ/T 70015-2022 :Test Methods and Evaluation of Pressure in Knitted Compression Garments

Features

1.Accurate measurement of garment pressure at multiple body locations with high-resolution sensors.

2.Supports bothstaticanddynamic testing, simulating real-life movement and posture.

3.Pressure mapping allows objective evaluation of garment comfort and functionality.

4.Dynamic mannequin posture designed to maintain full body integrity, with clearance behind knees.

5.Enables design optimization for sports, medical, and fashion applications through data-driven analysis.

Parameters

Item	Specifications
Pressure Mannequin	Average Asian female body type, height: 155 ~ 165 cm
Pressure Measurement Range	0 ~ 90 mmHg
Test Accuracy	≤0.1 mmHg
Resolution	≤0.1 mmHg
Sensors	26 independent sensors, each measuring a separate point. The sensor surface is flat and stable, with no mutual interference between measurement points.

Accessories

1.Full-body mannequin (Asian female average build, height 155–165 cm)

2.26-point high-precision pressure sensor array

3.Data acquisition and analysis software

4.Adjustable fixtures for dynamic posture simulation

5.Calibration tools and reference pressure standards

Test Procedures

I. Equipment Preparation and Calibration

Parameter Verification: Ensure equipment complies with FZ/T70015-2022 standards. The pressure manikin uses the average Asian female physique (height 155–165 cm).

Sensor Inspection: All 26 sensors must have flat surfaces and stable configurations to ensure independent measurements without interference.

‌Range Calibration: Pressure measurement range 0–90 mmHg, test accuracy ≤0.1 mmHg, resolution ≤0.1 mmHg.

II. Test Procedure

‌1. Static Testing:

Place the garment over the pressure manikin and adjust to the standard posture (void space behind knees).

Activate the equipment, record pressure values at each point, and analyze pressure distribution uniformity.

2. Dynamic Testing:

Simulate movement postures (e.g., running, jumping) and observe pressure changes.

Focus on pressure values in high-activity areas (e.g., armpits, waist).

III. Data Interpretation and Optimization

1. Comfort Assessment:

Excessive pressure (>90 mmHg) may cause constriction, while insufficient pressure fails to provide adequate support.

Optimize pressure distribution by adjusting fabric elasticity or cutting techniques.

2. Function Verification:

Performance compression garments must deliver moderate pressure to key muscle groups (e.g., thighs, calves) to reduce muscle vibration.

Medical garments must ensure uniform pressure distribution to prevent blood circulation obstruction.

Other supplier products

	Helmets Designated Protection Areas Tester	Main Purposes 1. Used to mark test points and test lines on helmets. 2. Used for line - marking according to different test standards. 3. Used t...
	Bending Test device	Compliance Standards ASTM D790 (Plastics Flexural Properties) ISO 178 (Flexural Strength of Rigid Plastics) SAE J2748 (Automotive Composite Flex...
	Alcohol Abrasion Testing Machine (for Alcohol abrasion tester)	Product Introduction: This machine adopts variable convex shaft structure, diameter Japanese original ball drive, so that the workpiece can move w...
	Dry Type Human Thermal Manikin for Comfort Analysis	Whats/App: +86 156 1874 6768 Web: standard-groups.com Application The 16-Segment Heated Thermal Manikin is used in the following application are...
	G651 national standard shoe bending tester	Product Introduction: National standard shoe bending testing machine is specialized in testing finished shoes and soles, after a long time, fixed ...

供应产品

Same products

	Full-Body Garment Stress Tester,FZ/T 70015	卖方: Standard International Group (HK) Limited	TheFull-Body Garment Stress Testeris a precision instrument designed to quantify the pressure exe...
	Industrial Dry Cleaning Machine,industrial garment steamer	卖方: Standard International Group (HK) Limited	TheIndustrial Dry Cleaning and Energy-Saving Dryer Machinesare designed for high-performance, rel...
	MST Medical Compression Stocking Tester,compression sock tester	卖方: Standard International Group (HK) Limited	The MST Medical Compression Stocking Tester is a professional instrument designed to evaluate the...
	MMT Liquid Water Separation Tester,MMT Liquid Water Analysis Tool	卖方: Standard International Group (HK) Limited	Applications Textile Manufacturing:Testing waterproof fabrics for outdoor gear R&D:Developi...
	Dental material color stability tester	卖方: Standard International Group (HK) Limited	Application The applications of color stability testers for dental materials are mainly reflecte...