G678W-L cold resistance testing machine for shoes
Shoes cold resistance testing machine is used to test finished shoes, rubber, sole, synthetic leather, plastic and other test requirements under various low temperature environment to understand the ability of various materials or finished shoes to adapt to low temperature climate or cold terrain area, this instrument is made of rust SUS steel, can be installed with a variety of different test fixtures. In order to meet the different standards of various tests.
Meet the standard:
ASTM D17900, EN ISO 20344, HG/T 2411, HG/T 2871, DIN 53351, SATR TM55, Adidas GE-24, GE-57, GB/T 20991-2007 and other standards
Main parameters of cold box:
1, balanced temperature regulator humidity control system
2, temperature range: -25℃ —— +150℃
3, temperature fluctuation: ≤±0.5℃
4, temperature uniformity: ≤2℃
5, temperature accuracy: ±0.2℃
6, heating time: +25℃→+85℃ room temperature to 85℃ about 30 minutes no load
7, cooling time: +25℃→-40℃ room temperature to -40℃ about 50 minutes no load
8. Lead hole: φ50mm 1 （with 1 rubber plug）
9, heating rate: 3 —— 5℃/min（average）， cooling rate: 0.7 —— 1℃/min（average）
Shoe thermal test fixture set:
A: Cold medium: composed of 5mm diameter and 4kg total mass of stainless steel balls
B: Test copper plate: （350±5）*（150±1）*（5±0.1）mm
C: thermometer: accuracy is ±0.5 ° C
The fixture group should be configured according to actual test requirements or other standard requirements.
在线联系供应商
Other supplier products
 |
Mask synthetic blood penetration tester | Standards: GB 19083-2010 Technical requirements of medical face masks - Anti-penetration property of 5.5 synthetic blood. YY/T 0691-2008 Clothin... |
 |
Carpet Static Load Tester | Instrument Features - Simulate the imprints caused by furniture - Meet international standard requirements - Combine the static load tester wit... |
 |
Strength Tester for Lead - end of Photovoltaic Modules | Standard IEC 61215-2:2016: Terrestrial Photovoltaic (PV) Modules – Test Requirements for Electrical and Mechanical Components CE Certificat... |
 |
Femoral Stem Neck Prostheses Fatigue Testing Machine | Standard YY/T 0809.6 (China): Specifies neck fatigue testing for femoral stems in partial/total hip arthroplasty. ISO 7206-6 (International): D... |
 |
Hand cranking Textile Crockmeter ISO 105 D02 X12 AATCC 8/165 | Introduction Manual friction fastness tester is the most commonly used instrument for the textile industry to detect the color fastness of the fab... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
