Rupture strength tester
The Rupture Strength Tester is designed to evaluate the mechanical pressure resistance and rupture strength of photovoltaic module components under controlled pressurization conditions. The system applies uniform hydraulic or pneumatic pressure to determine the failure threshold of module glass, backsheets, and encapsulation structures, supporting safety qualification and structural reliability assessment of photovoltaic modules.
Application
(1) Rupture strength testing of photovoltaic module front glass
(2) Pressure resistance evaluation of PV module backsheets and encapsulants
(3) Safety verification of single-glass and dual-glass photovoltaic modules
(4) Mechanical integrity assessment under simulated wind and snow loads
(5) Quality control and type approval testing in PV module manufacturing
(6) Failure analysis and material comparison in PV R&D laboratories
Standards
(1) IEC 61730-2 – Photovoltaic (PV) Module Safety Qualification – Requirements for Testing
(2) UL 61730 – Safety Standard for Photovoltaic Modules
(3) CE Certification (Conformité Européenne)
Features
(1) Wide Pressure Capability: Suitable for rupture testing of thin-film, crystalline silicon, and dual-glass PV modules.
(2) High-Resolution Pressure Control: Enables early detection of micro-cracking and progressive structural failure.
(3) Multi-Unit Measurement Interface: Supports kPa, psi, and kg/cm² for international testing requirements.
(4) Enhanced Safety Structure: Reinforced test chamber allows safe observation of specimen rupture.
(5) Automated Test Control: Preset pressure ramp and holding sequences reduce operator variability.
(6) Integrated Data Recording: Pressure–time curves and rupture values stored for traceability and analysis.
(7) Robust Construction: Stainless steel frame ensures long-term stability under repeated high-pressure operation.
Parameters
| Parameter | Specification |
|---|---|
| Pressure Range | 250–5,600 kPa (36–812 psi) |
| Pressure Resolution | 0.01 kg/cm² |
| Holding Pressure | 5 kg/cm² (adjustable) |
| Control Accuracy | ±1% FS (full scale) |
| Air Source Requirement | ≥6 kg/cm² (customer-provided) |
| Power Supply | 220V AC, 50/60Hz, single-phase |
| Dimensions | 560 mm (W) × 470 mm (D) × 550 mm (H) |
| Weight | 60 kg (net) |
Accessories
(1) Testing Fixtures: 1× specialized clamping fixture for 2–20 mm module thickness
(2) Membranes: 2× high-temperature rubber membranes (up to 300°C)
(3) Calibration Tools: 5× aluminum foil calibration discs
(4) Consumables: 85% glycerin solution for hydraulic calibration, disposable dust filters
(5) Safety Equipment: Safety goggles (ANSI Z87.1), emergency pressure release key
(6) Documentation: Multilingual quick-start guide and IEC/UL compliance certificates
Test Procedures
(1) Install the PV module specimen securely into the clamping fixture.
(2) Select pressure unit, ramp rate, and holding parameters via the touchscreen interface.
(3) Initiate pressurization and monitor real-time pressure increase.
(4) Maintain holding pressure as specified or continue ramping until rupture occurs.
(5) Record rupture pressure, pressure–time curve, and failure mode automatically.
Maintenance Information
(1) Inspect sealing membranes and clamping fixtures regularly for wear or deformation.
(2) Verify pressure sensor calibration at scheduled intervals.
(3) Clean the test chamber after each rupture test to remove debris.
(4) Check safety valves and electronic cut-off functions before routine operation.
(5) Store the tester in a clean, dry environment to maintain long-term accuracy.
在线联系供应商
Other supplier products
 |
Transmission belt flammability and flame diffusion characteristics tester | Product Introduction The conveyor belt flammability and flame diffusion tester is suitable for testing the flammability and flame propagation char... |
 |
Helmet Projection and Surface Friction tester | The helmet projection and surface friction tester is a device used to test the frictional force between the helmet surface and other objects. Its m... |
 |
High Velocity Impact Testing Machine | Main Purpose To test the impact - resistance performance of glasses, goggles and face shields at a certain speed. Applicable Standards SNELL S... |
 |
Photovoltaic module backplane peeling strength testing machine | The Photovoltaic Module Backplane Peeling Strength Testing Machine is a specialized device designed to evaluate the peeling strength of photovoltai... |
 |
High Velocity Impact Testing Machine | Main Purpose To test the impact - resistance performance of glasses, goggles and face shields at a certain speed. Applicable Standards SNELL S... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
