Rupture strength tester
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The Rupture Strength Tester is designed to evaluate the mechanical pressure resistance and rupture strength of photovoltaic module components under controlled pressurization conditions. The system applies uniform hydraulic or pneumatic pressure to determine the failure threshold of module glass, backsheets, and encapsulation structures, supporting safety qualification and structural reliability assessment of photovoltaic modules.
Application
(1) Rupture strength testing of photovoltaic module front glass
(2) Pressure resistance evaluation of PV module backsheets and encapsulants
(3) Safety verification of single-glass and dual-glass photovoltaic modules
(4) Mechanical integrity assessment under simulated wind and snow loads
(5) Quality control and type approval testing in PV module manufacturing
(6) Failure analysis and material comparison in PV R&D laboratories
Standards
(1) IEC 61730-2 – Photovoltaic (PV) Module Safety Qualification – Requirements for Testing
(2) UL 61730 – Safety Standard for Photovoltaic Modules
(3) CE Certification (Conformité Européenne)
Features
(1) Wide Pressure Capability: Suitable for rupture testing of thin-film, crystalline silicon, and dual-glass PV modules.
(2) High-Resolution Pressure Control: Enables early detection of micro-cracking and progressive structural failure.
(3) Multi-Unit Measurement Interface: Supports kPa, psi, and kg/cm² for international testing requirements.
(4) Enhanced Safety Structure: Reinforced test chamber allows safe observation of specimen rupture.
(5) Automated Test Control: Preset pressure ramp and holding sequences reduce operator variability.
(6) Integrated Data Recording: Pressure–time curves and rupture values stored for traceability and analysis.
(7) Robust Construction: Stainless steel frame ensures long-term stability under repeated high-pressure operation.
Parameters
| Parameter | Specification |
|---|---|
| Pressure Range | 250–5,600 kPa (36–812 psi) |
| Pressure Resolution | 0.01 kg/cm² |
| Holding Pressure | 5 kg/cm² (adjustable) |
| Control Accuracy | ±1% FS (full scale) |
| Air Source Requirement | ≥6 kg/cm² (customer-provided) |
| Power Supply | 220V AC, 50/60Hz, single-phase |
| Dimensions | 560 mm (W) × 470 mm (D) × 550 mm (H) |
| Weight | 60 kg (net) |
Accessories
(1) Testing Fixtures: 1× specialized clamping fixture for 2–20 mm module thickness
(2) Membranes: 2× high-temperature rubber membranes (up to 300°C)
(3) Calibration Tools: 5× aluminum foil calibration discs
(4) Consumables: 85% glycerin solution for hydraulic calibration, disposable dust filters
(5) Safety Equipment: Safety goggles (ANSI Z87.1), emergency pressure release key
(6) Documentation: Multilingual quick-start guide and IEC/UL compliance certificates
Test Procedures
(1) Install the PV module specimen securely into the clamping fixture.
(2) Select pressure unit, ramp rate, and holding parameters via the touchscreen interface.
(3) Initiate pressurization and monitor real-time pressure increase.
(4) Maintain holding pressure as specified or continue ramping until rupture occurs.
(5) Record rupture pressure, pressure–time curve, and failure mode automatically.
Maintenance Information
(1) Inspect sealing membranes and clamping fixtures regularly for wear or deformation.
(2) Verify pressure sensor calibration at scheduled intervals.
(3) Clean the test chamber after each rupture test to remove debris.
(4) Check safety valves and electronic cut-off functions before routine operation.
(5) Store the tester in a clean, dry environment to maintain long-term accuracy.
Send product request
Other supplier products
 |
Flame Penetration Fuel Test System for Thermal and Acoustic Insulation Materials | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Flame Penetration Fuel Test System for Thermal and Acoustic Insulation Materials is a d... |
 |
Industrial Linear Reciprocating Friction and Wear Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards GB/T 3960-2016 Plastics – Determination of Sliding Wear Properties GB/T 1... |
 |
Affordable Wear Track Profilometer tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com A wear profiler is a device used to measure the characteristics of worn surfaces, providing... |
 |
Filter membrane pore analysis tester for ASTM F316 membrane integrity testing | Get a quote： Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards (1) ASTM E1294 — Standard Test Method for Pore Size Characte... |
 |
Tensile and Shear Tester STD - FB1 - A | Whats/App: +86 156 1874 6768 Web: standard-groups.com The Tensile and Shear Tester analyzes hand movements-referred to as "tensile"and "shear"-pe... |
Same products
 |
Battery Diaphragm Gas Permeability Tester ISO | Seller: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Battery Diaphragm Gas Permea... |
 |
Torsion Testing Tester ASTM, JIS, and DIN | Seller: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Universal Torsion Testing Ma... |
 |
Wire Torsion and Winding Tester ASTM and JIS | Seller: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Wire Torsion and Winding Tes... |
 |
Metal Wire Repeated Bending Tester ISO/DIS 7801 | Seller: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Repeated Bending ... |
 |
Metal Wire Wrap Tester ISO 4101 | Seller: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Wrap Tester is de... |
