Safety Helmets Impact and Penetration Resistance Tester
The Safety Helmets Impact and Penetration Resistance Tester is a dual-function testing system designed to evaluate helmet safety under both impact and penetration conditions. It ensures compliance with national and international standards, supporting quality control, certification testing, and research applications.
Application
(1) Impact resistance testing for industrial helmets (e.g., construction safety helmets, GB/T 2812 certified)
(2) Impact testing for cycling helmets (road, mountain, BMX)
(3) Impact testing for motorcycle helmets (full-face, modular, open-face)
(4) Penetration resistance testing for climbing helmets and rope-access helmets
(5) Custom helmet testing for sports or military applications
(6) R&D and batch quality control for OEM helmet lines (including EN 960 S/M/L headforms)
(7) Certification testing for GB/T 2811-2019, ISO 6220-2, and CE/EN compliant helmets
Standards
(1) GB/T 2811-2019 – Helmet safety and impact resistance
(2) GB/T 2812-2006 – Testing methods for impact absorption and penetration resistance
(3) ISO 6220-2 – Road vehicles restraint systems energy absorption test methods
(4) EN 960 – Headforms for protective helmet testing
(5) CE Certification (Conformité Européenne)
Features
(1) Dual-Function Versatility: Rapid fixture exchange allows switching between impact and penetration tests in under 10 minutes
(2) Ultra-Precision Impact Analysis: 5 kg hemispherical hammer with 1,000 mm drop height and 20,000 N force sensor at 0.1 N resolution
(3) Penetration Resistance Validation: 3 kg conical tip hammer (60° ±0.5°, 40 mm min., 45–50 HRC) simulating sharp object impacts
(4) Smart Data Acquisition: Real-time force curves with pass/fail alerts and 1 ms resolution
(5) Industrial Durability: 4 m steel frame with anti-vibration design, IP65-rated control panel
(6) Safety Systems: Light curtain, energy-absorbing base, and emergency stop
(7) Universal Compatibility: EN 960 headforms (S/M/L) and custom 3D-printed headforms for specialized helmets
Parameters
| Specification | Impact Test | Penetration Test |
|---|---|---|
| Drop Height | 1,000 ±5 mm | 1,000 ±5 mm |
| Hammer Weight | 5.0 ±0.1 kg | 3.0 ±0.05 kg |
| Tip Geometry | Hemisphere (R50 ±1 mm) | Cone (60° ±0.5°, 40 mm min.) |
| Force Sensor | 20,000 N, 5 kHz sampling | N/A (mechanical stop) |
| Data Resolution | 0.1 N | 0.1 mm displacement |
| Frame Height | 4,000 mm | 4,000 mm |
| Power Requirements | 220V/110V AC, 50/60Hz, 800 W | 220V/110V AC, 50/60Hz, 800 W |
Accessories
(1) Headform Kit: EN 960 S/M/L sizes with polyurethane skin coating
(2) Hammer Set: Impact (5 kg) and penetration (3 kg) hammers with storage case
(3) Calibration Tools: NIST-traceable force gauge and Rockwell hardness tester
(4) Safety Kit: Light curtain, energy-absorbing base mat, emergency stop button
(5) Software License: HelmetImpact Pro, cloud-connected with API integration for QMS systems
(6) Installation & Training: On-site setup by certified engineers, 16-hour virtual operator training
Test Procedures
(1) Install the helmet on the selected headform.
(2) Select impact or penetration test mode and attach the corresponding hammer.
(3) Set drop height, test parameters, and safety interlocks via the HMI.
(4) Conduct the test; monitor real-time force/displacement curves.
(5) Record peak forces and penetration measurements; evaluate against standard requirements.
(6) Generate automated pass/fail reports and export data for QC or certification.
Maintenance Information
(1) Inspect hammers, headforms, and force sensors regularly for wear or damage.
(2) Clean frame, rails, and fixtures with non-corrosive solution.
(3) Verify calibration of force sensors and drop heights periodically.
(4) Lubricate linear bearings and moving components as per schedule.
(5) Store in a clean, dry environment to maintain precision and service life.
在线联系供应商
Other supplier products
 |
Electric notch machine丨Electric notch chamber | Product Introduction: Plastic electric notch prototype is a cantilever beam, simply supported beam impact testing machine to do the impact toughne... |
 |
Solid Auto - ignition Point Tester | This tester determines the self - ignition characteristics of solid chemical products by placing the substances in a 20mm - side - length cubic wir... |
 |
Surgical Mask Flame Retardant Test machine | Flame-retardant tester for surgical mask, In case of the mask is accidentally exposed to flame, its flame-retardant performance is directly related... |
 |
Micro Controll Four-ball Friction Tester | The microcomputer-controlled four-ball friction testing machine uses a sliding friction method under point contact pressure conditions at the extre... |
 |
Sleeping Bag Flammability Tester -ASTM F1955 | Standards： ASTM F1955.CPAI 75 Application： Sleeping Bag Flammability Tester, to determine the flammability resistance of sleeping bag. Both manu... |
Same products
 |
Falling Sand Abrasion Test machine | 卖方: Standard International Group (HK) Limited | The sand abrasion tester is a specialized testing device used to evaluate the abrasion resistance... |
 |
Conveyor Belt Drum Friction Testing Machine | 卖方: Standard International Group (HK) Limited | Main Purposes of Conveyor Belt Drum Friction Testing Machine The conveyor belt drum friction tes... |
 |
Dry Sand Rubber Wheel Wear Tester | 卖方: Standard International Group (HK) Limited | The dry sand rubber wheel abrasion tester is mainly used to test the abrasion resistance of mater... |
 |
Sliding Bearing Fatigue Testing Machine | 卖方: Standard International Group (HK) Limited | The sliding bearing fatigue testing machine is an important testing device, mainly used to evalua... |
 |
High temperature vacum friction & wear tester | 卖方: Standard International Group (HK) Limited | The working principle of a high-temperature vacuum friction and wear testing machine is to simula... |
