Safety Helmet Roll-off Testing Equipment
Whats/App: +86 156 1874 6768
Web: standard-groups.com
The safety helmet retention test equipment is a device used to evaluate the stability of a helmet's fit when subjected to impact. By simulating the pulling forces and impact scenarios of an accident, it accurately assesses the reliability of the helmet's retention system, providing a rigorous technical safeguard for the safety of cyclists. The equipment mainly consists of a simulated head form, a tensile loading system, an impact track, and a data acquisition system. During the test, the helmet is secured to the simulated head form according to standard wearing procedures, and the length of the helmet straps and the tightness of the buckles are adjusted to ensure a fit that matches actual wearing conditions.
Application
Apply an initial load of a certain force to the rear of the helmet. Then, let a weight specified by the standard fall from a certain height so that the impact force is also applied to the helmet. In this way, the wearing stability performance of the helmet can be evaluated.
Standard
IS 4151:Indian Standard for Protective Helmets
ECE R22.05:Uniform Provisions Concerning the Approval of Protective Helmets and Their Visors for Drivers and Passengers of Motor Cycles and Mopeds
Feature
Dynamic Tensile Testing: A tensile force is applied to the helmet using a tensile loading system, and the maximum tensile force is recorded to ensure the helmet does not detach during the test.
Impact Testing: The helmet is worn and slid down a track to impact a rigid obstacle at a specific speed, and whether the helmet detaches is recorded.
Data Acquisition: An accelerometer records the impact force on the headform, comprehensively evaluating the stability of the fastening system under dynamic impact.
Safety Protection: The equipment is equipped with a safety enclosure to prevent injury from flying helmet fragments during testing.
Parameters
| Item | Detail |
|---|---|
| Mass of initial load | 3 kg ± 0.1 kg |
| Mass of falling weight | 10 kg ± 0.01 kg |
| Lowering height | 0.5 meters ± 0.01 meters |
| Measuring method | manual |
| Electricity | 220V 50HZ |
| Test theory | vertical descent |
Accessoriess
Anthropomorphic headform
Strap clamp
Force sensor
Impact drive assembly
Data acquisition and analysis system
Protection and limiting devices, etc.
Test Procedures
1. previously to the ambient temperature and sanitary conditions for the conditions of the helmet, should be placed on the appropriate head shape and fixed in the appropriate head.
2. In the median vertical plane of the helmet, a device that guides and releases the fall with a total mass of 3 kg ± 0.1 kg is attached to the rear of the shell.
3. 10 kg ± 0.01 kg of falling mass is released and lowered from a height of 0.5 m ± 0.01 m. The guiding device should ensure that the impact velocity is not less than 95% of the theoretical velocity.
在线联系供应商
Other supplier products
 |
Micro Rapid Closed Cup Flash Point Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Reference Standards： SH/T 0768. SN/T 3077.1. DL/T 1354. ASTM D6450 SN/T 3077.2. ASTM D7094... |
 |
10kN Universal Testing Machine丨10kN Universal Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Product Introduction The electronic universal testing machine is a classic and practical m... |
 |
ASTM D6830 Aerosol Sensor Test System | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standards This system complies with and supports: (1) GB/T 14295-2019 – Air filters... |
 |
Intramedullary Nails Four - point Bending Fatigue Tester | Whats/App: +86 156 1874 6768 Web: standard-groups.com Standard YY/T 0591-2011: Chinese standard specifying bending fatigue test methods for intr... |
 |
Constant elongation stress meter | Whats/App: +86 156 1874 6768 Web: standard-groups.com A Constant Elongation Stress Meter is a specialized testing device designed to measure the ... |
Same products
 |
Battery Diaphragm Gas Permeability Tester ISO | 卖方: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Battery Diaphragm Gas Permea... |
 |
Torsion Testing Tester ASTM, JIS, and DIN | 卖方: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Universal Torsion Testing Ma... |
 |
Wire Torsion and Winding Tester ASTM and JIS | 卖方: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Wire Torsion and Winding Tes... |
 |
Metal Wire Repeated Bending Tester ISO/DIS 7801 | 卖方: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Repeated Bending ... |
 |
Metal Wire Wrap Tester ISO 4101 | 卖方: Standard Groups | Get a quote： Whats/App: +86 185 0176 3615 Web: qinsun-lab.com The Metal Wire Wrap Tester is de... |
