.

HIGH SPEED STRAIGHTENING & CUTTING MACHINE

  1. HIGH SPEED STRAIGHTENING & CUTTING MACHINE,Double Wire Straightening Cutting Machine Manufacturer,Double Wire Straightening Cutting Machine Supplier

    Double Wire Straightening Cutting Machine Manufacturer

    Double Wire Straightening Cutting Machine Supplier

    HIGH SPEED STRAIGHTENING & CUTTING MACHINE use the high speed rotating spinner to make straightening. This machine make straight bar from coil in high efficiency.

    material characteristics

    Model No.

    KZT3-1DX

    KZT5-12X

    KZT8-14TX

    KZT12-16X

    Hot rolled smooth surface coiL

    φ3 -φ10

    φ5-φ12

    φ8-φ14

    φ12-φ16

    Hot rolled ribbed coilyieLd Strength 335Mpa

    φ3 -φ8

    φ5-φ12

    φ8-φ14

    φ12-φ16

    Hot rolted ribbed coilyieLd strength 4Q0Mpa

    φ3 -φ8

    φ5-φ12

    φ8-φ14

    φ12-φ16

    Cold rolled coil

    φ3 -φ10

    φ5-φ12

    φ8-φ14

    φ12-φ16

    Cut-to-length (m)

    1-12

    Straightening speed (m/min)

    70-100-130

    straightness accuracy (mm/m)

    2

    Cold rolled coil (mm)

    ≤±1

    Cold rolled coil (kw)

    22+7.5

    37+7.5

    45+7.5

    STRAIGHTENING & CUTTING MACHINEPRINCIPLE

    Maximum carrying capacity 2,000Kg.Equipped with wire guide and safety funnelEquipped with 1set of vertical payoff and 1set of guide funnel3. WIRE INLET FEED UNIT

    Two independent incoming towing devices.Each device is made up of two pulleys whose aim is to feed the wire toward to the rotating unit.The pulley is equipped with two races whose profile depends on the shape and dimensions of the wire to be processed.The upper pulley pressure is adjusted by screw and pneumatic clamping.

    The most important component of the machine.There are five couples of dies inside the body. The machine is normally supplied with two types dies (standard cast-iron dies) for the process of the small and large wires.

    1. WIRE OUTLET FEEDUNIT

    Out-feed unit is made up of two pulleys whose aim is to drag the wire from the rotating unit to the cutting unit.

    The pulley is equipped with two races whose profile depends on the shape and dimensions of the wire to be processed.

    The upper pulley pressure is adjusted by screw and pneumatic clamping.

    The cut unit is made up of an arm within which there is cutting knife, moved by an independent servo-motor operating on a can cutting the wire to the required length.

    12m collecting bench with preselecting rod counter (buffering device) and collecting pocket.

    The cutting control device (length measuring) is mounted in the frame. Any required length between 1,000-12,000mm can be setup manually.

    Siemens electric cabinetButton and touchable screen coordinated operation system



在线联系供应商

至: SKZ Intelligent Equipment Co. , Ltd.
Your E-mail:
消息正文:


Send to other suppliers

Other supplier products

Wire Mesh Welding Machine
Wire Mesh Welding Machine The intelligent steel mesh production robot KZH3300KX can be used for the production and welding of standard mesh and perforated mesh for prefa...
High Speed Straightening Cutting Machine
High Speed Straightening Cutting Machine HIGH SPEED STRAIGHTENING & CUTTING MACHINE use the high speed rotating spinner to make straightening. This machine make straight bar from coi...
bridge Stirrup Bender
bridge Stirrup Bender Grid arch ,as a kind of tunnel arch is commonly used in highway, railway tunnel, and the initial support in mine roadway construction . However,...
DOUBLE WIRE STRAIGHTENING & CUTTING MACHINE (KZ12TX)
DOUBLE WIRE STRAIGHTENING & CUTTING MACHINE (KZ12TX) DOUBLE WIRE STRAIGHTENING & CUTTING MACHINE (KZ12TX),High Speed Straightening Cutting Machine,Double Wire Straightening Cutting Machine High S...
rebar shear-line Factory
rebar shear-line Factory This cutting machine is used to cut high-tensile steel bars of big diameter into expected-length pieces which will be then sorted and stored, al...
供应产品

Same products

Semi-Solid Die Casting
Semi-Solid Die Casting 卖方: Shanxi Rayforce Manufacture Co., Ltd. Based on the theory of stir cast invented by Mr. D.B. Spencer and M.C.Flemings, the semisolid die...
Sand Casting
Sand Casting 卖方: Shanxi Rayforce Manufacture Co., Ltd. Sand casting is the most commonly applied method for casting the metal part. It suits most of the...
Resin Sand Casting
Resin Sand Casting 卖方: Shanxi Rayforce Manufacture Co., Ltd. Resin sand castingis a kind of floor molding process, by mixing the resin with quartz sand and so...
Low Pressure Die Casting
Low Pressure Die Casting 卖方: Shanxi Rayforce Manufacture Co., Ltd. The low pressure die casting is to let the melted metal flow into the casting mold under a certai...
Lost Wax Investment Casting
Lost Wax Investment Casting 卖方: Shanxi Rayforce Manufacture Co., Ltd. The lost-wax casting process can differ depending on the application and the requirement, but it ...