Forging Process
Create Die Mold
Create a die mold is the first step for the metal forging process, it is critical and essential step for the die mold forging process.
We have a die mold maker who had been working with us for near 20 years, with rich experience, who can design the mold according to customers’ drawings, samples very quickly and with very high quality.
Material Cutting and Heating
Material Cutting and Heating
Base on the drawings or samples, our engineers will calculate the bar material diameter and length we need, then we will select the correct bar material and cut it in suitable billets.
The billets will be sent to the high frequency furnace for hearting to about 1000°C, then start the press.
Press
Press
The heated billet with 1000° C will be put at the middle of the dies, close the dies, the material will be shaped as the customers requirement. When open the dies, we get a raw parts with the fin around.
Cutting the Fin
Cutting the Fin
The raw parts with the fin will put in a cutting mold to remove the fin, after the fin removed, we get the raw forgings, the forging process is completely.
Heating Treatment
Heating Treatment
To get better strength or machining hardness, eliminate forging stress and improve metal cutting performance. we need put the forging in heat treatment furnace. Heat the parts near or above its critical temperature, held for a certain time, then cooling the metal in some medium like air, water or molten salts.
The hot forging processincludes annealing, case hardening, tempering, normalizing and quenching, nitriding, cyaniding etc.
Sand Blasting
Sand Blasting
To remove the oxide layer of the forging and get a uniformed surface, we will place the parts in sand blast machine. After sand blasting, the surface is quite uniform.
Machining
Machining
To get accurate dimensions, the machining process is needed. In my factory, with more than 40set machining, we can machine the forgings in turning, drilling, milling, grinding, that means, you just need provide the drawings or samples, we will make finished parts according to your request.
Quality Inspection
Quality Inspection
Every parts in my factory must be inspected the quality before leading to my customers. This is very important to process, we have various inspection tools and experienced inspectors in my factory. The defected parts is not allowed to ship to any customer.
Packing
Packing
We are experienced in export package, we will follow customers request to pack the parts, the plywood box or carton, pallets all available.
在线联系供应商
Other supplier products
HSG Engineering Hydraulic Cylinders | Brief Introduction: HSG type engineering hydraulic cylinder is a double-acting single-rod piston type hydraulic cylinder. It has the characterist... | |
Hydraulic Steering Control Units | The hydraulic steering gear is a hydraulic power steering type between the steering wheel and the steering mechanism, which does not need to be con... | |
Medium Excavator Series Cylinders | Brief Introduction: This type of cylinder is mainly used for medium excavators, including stick cylinders, boom cylinders, and bucket cylinders. U... | |
TG-E Multi-stage Hydraulic Cylinders | Product Introduction: TG hydraulic cylinder is a single-acting multi-section telescopic sleeve lift cylinder. It has the advantages of small size ... | |
Hydraulic Cylinder | JC Forging, a custom forged partsfactory in china, also specializes in the production of hydraulic equipment, including hydraulic cylinders, cycloi... |
Same products
Cassava Grater Machine(Cassava Grinding Machine) | 卖方: Nanyang Goodway Machinery & Equipment Co., Ltd. | Features of Cassava Grater Machine(Cassava Grinding Machine) Processing Capacity: 3-6Tons/hour ... | |
第二十五届广州国际锻造工业展览会 | 卖方: 广州巨浪展览策划有限公司 | 2025年广州巨浪国际金属暨冶金工业展览会 第二十五届广州国际锻造工业展览会 邀 请 函 主管批准单位:中华人民共和国商务部外贸司 广东省对外贸易经济合作厅 主承办单位: 广州巨浪展... | |
electric pipe grooving machine | 卖方: Hangzhou Evershining Machinery Co.,Ltd | Model: GC-12B Pipe Capacity:2”-12”(¢50 mm - ¢300 mm) Max wall thickness:6 mm Outpu... | |
Forged Clevis | 卖方: Hebei Golden-hammer forgings co., ltd | Product: Forged clevis Application: hydraulic cylinder Place of origin: Hebei, China (Mainl... | |
CNC Turning Shaft - CNC Turning Parts - CNC Turning Service | 卖方: Asianstar CNC Machining Company | Turning Shaft is one the most common CNC turning parts. It is made of metal or plastic materials ... |