corrugated carton 1-4 color printer die cutter slotter machine

Paper feeding section (one group)

1. Machine clutch:

1) An alarm bell is attached to the clutch of the electric control machine, and the alarm bell is continuously sounded during the travel to ensure the safety of the operators.

2) Pneumatic interlocking device, locking firmly, convenient and accurate.

3) The main motor adopts variable frequency motor and variable frequency controller, which can save energy and start stably. The motor start protection device is attached.

4) Self locking function of main engine: when the unit is not fully locked, the main engine cannot be started to ensure the machine and operators; When the main engine works normally, the clutch function of the unit is automatically locked to avoid machine and personnel injury caused by misoperation

2. Leading edge paper feeding system

1) Suction assisted paper feeding, 7.5kW high-pressure centrifugal fan, which can be adjusted according to the bending degree of paperboard

Variable frequency control of wind pressure to ensure high-speed and accurate transmission of warped paperboard and paperboard.

2) The paper lifting and dropping are driven by air cylinder, with rapid and powerful action.

3) The side baffle is adjusted by electric and computer touch screen (computer set value, automatic adjustment), the front baffle is adjusted manually and synchronously, and the rear baffle box is adjusted by electric.

4) Interlaced paper feeding device, (continuous or interlaced paper feeding can be selected as required)

5) The touch screen is installed to automatically display the production quantity and production speed, and the production quantity can be set.

7) The die cutting part is equipped with interlocking control switch to realize emergency stop, stop feeding or resume paper feeding (in addition, the whole machine acceleration and deceleration button is equipped)

8) Touch screen operation to realize the joint control of the whole machine,

Adjust the data of each unit directly behind the machine,

Convenient and fast.

3. Dust removal device

The machine is equipped with a pneumatic snap device, and the paperboard

Lateral positioning is more accurate to avoid waste.

(computer controlled snap time)

4. Computer device:

1) The main motor adopts frequency conversion motor, and the frequency converter adopts Taiwan Delta, which can save energy and power by up to 30%.

2) The fan is controlled by an independent frequency converter and the air pressure is adjustable.

3) The main screen adopts PLC control and man-machine interface.

4) The printing department, and die cutting department are equipped with automatic zeroing device (generally, cartons use automatic zeroing device, which can be adjusted to the correct position by trial printing two sheets)

5) Automatic plate lifting and dropping device, and the printing anilox roller rises and falls in sequence (computer adjusted delay) to avoid multiple ink dipping of the printing plate.

6) An ink shortage alarm device is set to monitor the working state of the ink supply system in real time to avoid ink-free operation.

7) The 10 inch color touch screen controls the paper feeding department, order storage, memory reset, production speed 30, 60, 90, 120 constant speed cruise, infrared photoelectric counting, and preset order processing quantity.

8) One button split reset function, one button reset after unit split and assembly, high degree of, and improve work efficiency.

5、 Printing department: (1-4 color printing is optional)

1. Printing roller:

1) Outer diameter: 468mm (including plate outer diameter: 5480mm).

2) The steel pipe surface is ground and plated with hard chromium. The roll body is engraved with reference lines in the horizontal and circumferential directions to facilitate plate alignment.

3) Do computer dynamic balance correction and run smoothly.

4) Ratchet fixed plate winding shaft.

5) Full plate hanging groove, applicable to 9mm-10mm plate hanging strip.

6) Loading and unloading the printing plate, the foot switch electrically controls the forward and reverse rotation.

7) The printing roller is electrically adjusted to the left and right in the axial direction, with a movement of about 10mm, and is equipped with a limit device (controlled by PLC touch screen)

2. Printing press roll:

1) The outer diameter is 5156.1mm. The steel pipe surface is ground and plated with hard chromium

2) Seamless tube fine processing, computer dynamic balance correction, smooth operation.

3) The gap dial of the printing press roller is adjusted manually, and the adjustment range is 0-12mm.

3. Upper and lower paper feeding rollers:

1) Upper roller, outer diameter 599mm, thick wall steel pipe, equipped with two paper feeding wheels (self-locking, no need to tighten screws, easy adjustment).

2) Lower roller, outer diameter 5154.3mm, thick wall steel pipe, surface grinding, hard chromium plating.

3) The gap dial of the paper feeding roller is adjusted manually, and the adjustment range is 0-12mm.

4. Steel anilox roller):

1) The outer diameter is 5215mm (number of lines: 180-250, number of lines optional)

2) The steel pipe surface is ground, pressed with chequer and plated with hard chromium. Do computer dynamic balance correction and run smoothly,

Consistent dot and uniform inking.

3) The anilox roller is attached with a wedge clutch, which is convenient and fast in ink leveling and washing. Pneumatic anilox roller automatic lifting device and idling device.

4) The chequer gap dial is adjusted manually.

6. Rubber roller:

1) Outer diameter 200mm.

2) The steel pipe surface is wrapped with wear-resistant rubber and corrected by computer dynamic balance.

3) The rubber roller has medium and high special grinding, and the ink transfer effect is good. The rubber hardness is 65-70 degrees.

7. Phase adjustment mechanism:

1) Planetary gear construction.

2) Printing phase adjustment PLC computer display adjustment (both operation and stop can be adjusted).

8. Ink supply system

1) Pneumatic diaphragm pump, stable ink supply, convenient and fast operation and maintenance.

2) Ink filter screen to filter impurities.

3) Circulating pneumatic inking

4) Ink shortage alarm device (when the ink amount is lower than the limit, the machine will alarm to avoid ink-free production)

9. Printing phase fixing device:

1) Cylinder brake.

2) When the machine adjusts the phase separately, the brake mechanism restricts the machine operation and maintains the fixed point of the original gear position.

4、 Die cutting part

1. Die roll (lower roll)

1) The outer diameter is 5432mm. (excluding die)

2) Cast steel material, surface grinding, hard chromium plating.

3) Computer dynamic balance correction to increase operation stability.

4) The distance between fixed screw holes of knife die is 100 * 100mm.

5) The applicable die height is 25.4mm.

6) The die cutting thickness is 16-18mm (for three-layer plate) and 13-15mm (for five-layer plate).

2. Rubber pad roll (upper roll)

1) The outer wall is 5434.2mm。

2) Cast steel material, surface grinding, hard chromium plating.

3) Computer dynamic balance correction to increase operation stability.

4) Manually adjust the clearance with the die roll.

5) The rubber pad is 8mm thick (outer diameter:? 0? 5450.2mm) and 250mm wide.

3. Traverse device:

1) Mechanical transverse 40mm, swimming device, die-cutting uniform weighing instrument, automatic compensation for linear speed, which can make the die-cutting rubber pad wear evenly and prolong the service life.

2) Electric device is adopted to improve the reuse rate of rubber pad, which can be used for 3-4 times.

3) The pneumatic automatic separation device of die-cutting roll reduces the wear of rubber pad, so as to improve the service life.

4. Electric plate matching device (optional)

The template roller (lower roller) can be moved laterally by ± 40mm,

For uneven die cutting at the edge of paperboard, electric adjustment can be used

To achieve uniform die-cutting edge material and convenient and fast adjustment.

Other supplier products

	automatic partition assembling machinery	automatic partition assembling machinery product presentation: 1.partition assemblermachine suitable for the auto insertion of all kinds of car...
	Automatic spiral paper core tube making machine	Automatic spiral paper core tube making machine Use 1, applicable substrate: mica tape, paper, insulating materials and film subcutting; 2. appl...
	corrugated cardboard flexo printing die cutting slotting machine	Purpose and characteristics: The machine can complete multi-color printing, die cutting, wire pressing and slotting. On the basis of similar produ...
	EPE net cover Machine	is a new type of soft packing material also named as pearl cotton. EPE foam sheet is an ideal substitute of traditional packing material. It has th...
	4 color flexo printer slotter die cutter machine	Functional features: 1. The whole machine adopts Schneider, Huichuan well-known brand and Taiwan Shengbang reduction motor, with stable and reliab...

供应产品

Same products

	受欢迎的全自动瓶装水液体灌装机	卖方: 河北盛辉泵业	全自动瓶装液体灌装机主要用于玻璃瓶或塑料瓶的灌装、送料和旋盖，常见于食品、化妆品、药品、日用化工、农药等领域。该机自动化程度高，机械设计合理，操作简便，包括无瓶灌装、无瓶旋盖和旋盖等功能。
	高精度小型规模 自动瓶盖包装机	卖方: 河北盛辉泵业	自动液体旋盖机设计用于自动灌装、自动旋盖和自动压盖，可实现无瓶不旋盖等功能。该机器可为牛奶、果汁、水等提供稳定均衡的输送。本机具有良好的灵活性。可适用于多种瓶型，并可根据瓶子高度和瓶盖大小进行调...
	新品小型立式智能自动咖啡粉灌装包装机	卖方: 河北盛辉泵业	自动咖啡粉灌装机是一种专门设计用于自动将粉末灌装到各种袋子中的设备。在食品工业中，确保精确、高效的包装，同时保持粉末的质量和新鲜度至关重要。
	价格最优的高效立式半自动单头液体灌装	卖方: 河北盛辉泵业	活塞式液体灌装机适用于植物油化工、日化、液体等各类粘性、非粘性、腐蚀性液体的定量小包装灌装和直线灌装。一方面，该机配有灌装量调节手柄，灌装速度快，灌装精度有保证。另一方面，灌装头采用防滴漏、防拉...
	用于饮料生产的多功能全自动饮用水液体瓶装灌装机	卖方: 河北盛辉泵业	全自动水液体灌装机，用于生产纯净水、矿泉水、天然水等PET瓶装饮用水，采用新技术，使塑料瓶的转运更加快捷方便，该机一次性完成洗瓶、灌装、封盖三道工序，卫生高效，高品质灌装阀确保灌装精度。