High and low temperature memory impact testing machine

Product Introduction:

Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics, cast stone, electrical insulation materials and other non-metallic materials impact toughness determination. The testing machine is an ideal test equipment for chemical industry, scientific research units, colleges and universities, quality testing departments, professional manufacturers laboratories and other units. It is a testing instrument with simple structure, convenient operation and accurate and reliable data.

Standards:

1.JB/T 8762-1998 "Plastic Simply supported beam Impact Testing Machine"

2.JJG145-2007 "Verification Regulations of Pendulum Impact Testing Machine"

3.GB3808 "Test of pendulum impact Testing Machine"

4.GB/T 1043.1-2008 "Rigid plastic simple support beam impact test method"

5.ISO 179-1993(E) "Plastics - Determination of impact strength of simply supported beams"

Technical indicators:

1. Impact energy: 2J/4J(simply supported beam); 2.75/5.5J(cantilever)

2. Sampling rate: 10us

3. Resolution: 16 bits

4. Load measurement accuracy: ≤1%

5. Impact knife Angle: 30°

6. Pendulum torque: simple beam 2.1436N.m, 1.0718N.m, 0.5359N.m

7. Cantilever beam 2.9474N.m, 1.4737N.m

8. Pendulum prelift Angle: 150°

9. Simple support beam:

1) Impact speed: 2.9m/s

2) The distance from the center of the pendulum shaft to the center of the sample: 230mm

3) Blade Angle: 30°

4) Blade radius: 2mm

5) Support corner radius: 1mm

6) Front Angle of support: 5°

7) Rear Angle of support: 10°

8) Support span: 40. 60. 70mm

9) Sample type and size (length × width × thickness)mm3:80×10×4mm, 50×6×4mm, 120×15×10mm

10. Cantilever beam:

1) Impact speed: 3.5m/s

2) The distance from the center of the pendulum axis to the center of the sample: 335mm

3) Blade Angle: 75°

4) Blade radius: 0.8mm

5) Front edge Angle: 5°

6) Blade back Angle: 10°

7) Sample type and size (length × width × thickness)mm3:

80×10×4mm

63.5 * 12.7 * 12.7 mm

63.5 * 12.7 * 6.4 mm

63.5 * 12.7 * 3.2 mm

Other supplier products

	Geomembrane Environmental Stress Cracking Resistance Tester	Scope of application: The stress cracking strength of polyolefin geomembrane was measured and evaluated by notch constant load tensile test. Durin...
	Dynamic footwear water penetration tester / SATRA TM 230	Application: Dynamic Footwear Water Resistance Tester is designed to determine the dynamic water resistance of all types of shoes. Principle： Th...
	Geosynthetics Bursting Strength Tester ASTM D	Meet the standard: ASTM D3786-2008.SL/T .etc Scope of application: It is used to determine the bursting strength of geotextiles, geomembranes an...
	AATCC Gray Scale for Color Change	Applicable Standards The AATCC Gray Scale aligns with international colorfastness evaluation protocols, including: AATCC Evaluation Procedure...
	Computer controlled horizontal tensile testing machine	Product Introduction: The microcomputer controlled horizontal tensile testing machine (hereinafter referred to as the testing machine) is mainly u...

供应产品

Same products

	Bottle Wall and Bottom Thickness Tester	卖方: Standard Group (Hong Kong) Limited	The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha...
	Pinhole Tester / Pinhole Testing Equipment	卖方: Standard Group (Hong Kong) Limited	The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ...
	Cork Puncture and Chip Detection Instrument	卖方: Standard Group (Hong Kong) Limited	The rubber stopper puncture debris detector is a device specifically used to detect the number of...
	Aluminum Ointment Tube Toughness Tester	卖方: Standard Group (Hong Kong) Limited	The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind...
	Vacuum leak tester / Vacuum leak instrument	卖方: Standard Group (Hong Kong) Limited	Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott...