Heat Storage Performance Tester ASTM F2731
Standards
ASTM F2731 ?Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems
Applications
The equipment is used to detect heat storage and thermal transfer characteristics of protective clothing, safety shoes, gloves, helmet and other materials, and determine the possibility that protective equipment can cause skin burns when exposed to heat.
Product Information
Introduction
Heat Storage Performance Tester provides standardized procedures and controls radiation heat conditions, providing repetitive measurement for heat storage and thermal transfer of protective fabric materials. Through measurement, the characteristics and rating of the material can be quickly identified, and the possibility of burn to the material is predicted through the integrated burn model of the instrument.
Product Details
Instrument Structure:
The equipment includes radiant heat source, sample holder, calorimeter induction component, pneumatic start transfer tray with water-cooled slide frame, compressor, DAQ/control system and combustion injury analysis program.
Instrument Features:
·Assessing the possibility of skin burns which is related to the heat energy storage performance of fabric.
·Automatic or manual test operation
·Radiant plate heat source (adjustable temperature) generates radiation energy, which matches with the spectral line density of building fire.
·The water-cooled sample sliders, electronic driven, realizes the precise control of the time of exposure on the heat source.
·The pneumatic compressor uses a low conductivity core bar to apply a 1PSI load on the sample.
·The system includes the integrated burn model, which predicts the severity of skin injuries, and calculates the estimated time of exposure leading to secondary burns.
·The combustion results are real-time values and the graph shows the skin layer interface temperature and combustion synthesis of Omega.
System Including:
·Dell PC laptop.
·ThermDAC software with a combustion model
·Signal conditioning circuit and USB interface
·Power supply and control cable, operator manual
·One-year warranty.
Laboratory Requirement:
·The laboratory should be well ventilated with dry compressed air source and cooling water supply pipe.
·The desktop device is designed for operation of horizontal or vertical radiant heat sources.
·It is recommended to operate in a vertical direction.
Standard Specification
·The radiant heat plate range is 0-0.25 CAL/cm2. adjustable.
·There are two types of hot plate operating modes: temperature control or heat flow control.
·The water-cooled sample slider supports sample and copper calorimeter exposes the sensor.
·Pneumatic control compression system
·The sample compression force can be adjusted by changing the air pressure in the cylinder.
·Sample size: 6x6ft (15x15cm). Gaskets with different thickness can be provided to compress the edges of smaller samples.
Technical Parameters
| Items | Parameters |
| Dimension | 24.5”x 17”x 14”H（62x43x36cm H） |
| Space required | 36”x 20”x 16”H（92x51x41cm H） |
| Power | 200-265VAC，50/60Hz, single phase. Maximum rated current is 5Amps |
| Compressed air | Clean/dry air 50-90PSI |
| Cooling water | 32.5℃. The flow rate is 100ml/min or greater (Local tap water is acceptable ) |
| Radiant heat plate range | 0-0.25cal/cm2, adjustable |
| Sample size | 6x6 inches (15x15cm) |
在线联系供应商
Other supplier products
 |
SCHAP Fogging Tester for Automotive & Textile Materials | Standard DIN 75201(Determination of the Evaporation Behavior of Materials in Motor Vehicles) ISO 6452(Rubber- or Plastics-Coated Fabrics — ... |
 |
Mask combustion tester | Standards: GB 19083-2010， EN 149, GB 2626, YY 0469 Applications: Mask combustion tester is to determine the fire resistance performance of... |
 |
Carpet Abrasion Resistance Tester | Standard ASTM D4157(Standard Test Method for Abrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)) ISO 12947-2(Textiles - Deter... |
 |
G651 national standard shoe bending tester | Product Introduction: National standard shoe bending testing machine is specialized in testing finished shoes and soles, after a long time, fixed ... |
 |
Dry microbial penetration tester | Standards: ISO 22612 YY/T 0506.5 Applications: Dry microbial penetration resistance tester DMPRT is to assess the penetration resistance t... |
Same products
 |
Plastic Smoke Density Tester F313 | 卖方: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | 卖方: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | 卖方: 上海千实精密仪器 | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | 卖方: 上海千实精密仪器 | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | 卖方: 上海千实精密仪器 | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
