Rubber Mooney Viscosity meter
Test principle:
The Mooney viscometer is used to measure the viscosity of rubber under specific conditions. In the test, the rubber sample was loaded into the mold cavity of the Mooney viscometer and the motor was started after preheating, and the rotor began to rotate and a certain shear torque was applied. At the same time, the rubber sample produces an equal and opposite resistance moment, which is displayed by the dial indicator installed at one end of the worm or directly through the computer, that is, the Mooney viscosity value.
Reference standard:
GB/T 1232 unvulcanized rubber - Determination of Mooney viscosity
GB/T 1233 rubber compound -- Determination of initial vulcanization characteristics -- Mooney viscometer method
HG-T 3242-2017 Rubber Mooney viscometer
ISO289 unvulcanized rubber -- determination by shear disc viscometer
ISO667 rubber compound - Determination of initial vulcanization characteristics - Mooney viscometer method
Technical parameters:
Measurement and control temperature range: normal temperature ——200℃
Torque measuring range: 0-100 Mooney value
Calibration accuracy: 100±0.5 Mooney value
Rotor speed: 2±0.02 RPM
Measurement time: 0-200 points
Ambient temperature: 0-35℃
Relative humidity: <80%
Test pressure: 11.5KN±0.5KN
Air pressure: 0.45-0.6MPa
Test requirements:
1) Scope: This specification specifies the test method of Mooney viscosity of rubber compound.
Note: Measuring range includes: Mooney viscosity.
2) Test tools: Mooney viscometer, electronic scale, scissors, heat insulation gloves
3) Sample requirements: Cut two rubber samples with a diameter of about 45mm and a thickness of about 3mm from the bubble-free rubber material, one of which has a circular hole with a diameter of about 8mm in the center of the sample (two pieces of rubber material weigh about 16g)。
4) Test conditions: the rubber material can be tested for more than 2 hours under laboratory conditions after processing, but not more than 10 days.
在线联系供应商
Other supplier products
 |
Medical injection needle puncture force test device | The needle puncture force simulates the skin tester with a 5.7-inch (120 x 90) single color LCD touch screen, which is displayed in the Chinese men... |
 |
Purity automatic extractor | Component Cleanliness Cabinet equipped with cleaning modes such as pressure jet cleaning, perfusion cleaning, spray cleaning, etc., the cleaning ... |
 |
Falling Sand Wear Tester | Applicable Standard JG/T 133-2000 ASTM D968-83 ASTMD333 ASTMD1395 ASTMD2205 Main Purposes It is mainly used to test the abrasion - resistanc... |
 |
Helmet Projection and Surface Friction tester | The helmet projection and surface friction tester is a device used to test the frictional force between the helmet surface and other objects. Its m... |
 |
Micro Rapid Closed Cup Flash Point Tester(Pensky Martens) | Automatic Flash Point Tester designed for accurate and repeatable determination of the flash point of petroleum products using the Pensky-Martens c... |
Same products
 |
Plastic Smoke Density Tester F313 | 卖方: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | 卖方: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | 卖方: 上海千实精密仪器 | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | 卖方: 上海千实精密仪器 | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | 卖方: 上海千实精密仪器 | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
