Bio-absorbable Internal Fixation Plates and Screws Test device
Standard
YY/T 0509-2009 (China): Specifies mechanical testing protocols for orthopedic plates/screws made of hydrolyzable polymers, including axial pull-out, torsion, and 4-point bending tests.
ASTM F2502-17 (International): Defines methodologies for evaluating the structural integrity of bioabsorbable fixation devices under physiological loading.
ISO 13779-4: Additional compliance for in vitro degradation testing of resorbable materials.
Product Advantages
Multi-Modal Testing: Single platform for axial pull-out, torsion, and 4-point bending tests.
Biodegradation Simulation: 37±1°C pH-controlled water bath with real-time conductivity monitoring.
High-Resolution Sensors: 0.001 N force/0.001 Nm torque resolution for fragile polymer testing.
Modular Fixturing: Self-centering clamps accommodate plates (20–100 mm) and screws (2.0–4.5 mm).
AI-Powered Analytics: Machine learning predicts degradation-induced strength loss over time.
Regulatory Compliance: Pre-loaded YY/T 0509/ASTM F2502 protocols with automated reporting.
Product Features
Electromagnetic Servo Actuator: 5 kN axial/1 Nm torsional capacity with programmable load ratios (R=0.1–10).
4-Point Bending Fixture: Anatomical curvature adapters replicate physiological stress patterns.
Dynamic pH Control: 37±1°C water bath with pH 5.5–8.0 adjustment for degradation studies.
High-Resolution Imaging: Built-in 5MP camera system for crack/corrosion analysis.
Safety Suite: Emergency stop, chemical-resistant enclosure, and leak detection.
Touchscreen Interface: Intuitive controls with pre-loaded ASTM/YY test sequences.
Accessories
Bioabsorbable Fixture Kit:
Self-centering plate clamps (20–100 mm compatibility)
Screw torque adapters (2.0–4.5 mm diameter)
pH-Controlled Water Bath:
15L capacity with recirculating pump
Corrosion-resistant titanium interior
BioTest Pro Software:
Automated degradation curve generation and strength retention analysis
21 CFR Part 11-compliant audit trail with blockchain timestamping
Remote monitoring via iOS/Android app
Operator Kit:
Calibrated torque wrench set (0.1–1 Nm)
Implant alignment jigs (ASTM F2502 compliant)
Calibration Bundle:
NIST-traceable force/torque calibration weights
pH electrode calibration solution
Safety Kit:
Chemical-resistant gloves
Acoustic enclosure with 25 dB noise reduction
Technical Parameters
| Parameter | Specification |
|---|---|
| Max. Axial Force | ±5.000 N (0.001 N resolution) |
| Max. Torsional Moment | ±1 Nm (0.001 Nm resolution) |
| Bending Span | 40–120 mm (1 mm increments) |
| pH Control Range | 5.5–8.0 (0.1 resolution) |
| Temperature Control | 37±1°C (PT1000 sensor) |
| Data Sampling Rate | 10 kHz (synchronized across 8 channels) |
| Power Requirements | 220V/110V ±10%, 50/60Hz, 1.200W |
| Dimensions (W×D×H) | 500 × 450 × 750 mm |
| Weight | 75 kg (net) / 90 kg (with bath) |
| Noise Level | <50 dB (A-weighted) |
在线联系供应商
Other supplier products
 |
Automotive Interior Materials Tactile Perception Quality Testing Procedure System | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application (1) Automotive seat surfaces: leather, fabric, synthetic leather, and composit... |
 |
Micro Controll Four-ball Friction Tester | The microcomputer-controlled four-ball friction testing machine uses a sliding friction method under point contact pressure conditions at the extre... |
 |
Oil Thread Leak Test System，ISO 16890 oil thread sealing performance tester | Test System for oil thread leak test of HEPA filter according to ISO 29463-4 (EN 1822-4). The oil thread test mentioned in ISO 29463-4 (1822-4), an... |
 |
Filter Flow Rate and Performance Test Equipment | Whats/App: +86 156 1874 6768 Web: standard-groups.com Application You can apply this test bench in the following scenarios: (1) Flow–pres... |
 |
Fiber Blend Ratio Test machine | Product Introduction: It is used to measure the resistance value with a certain density under a certain geometry, and then converts it into the sp... |
Same products
 |
Plastic Smoke Density Tester F313 | 卖方: Standard International Group (HK) Limited | The F313 Plastic Smoke Density Tester is a precision instrument designed to measure the specific ... |
 |
Xenon Test Chamber | 卖方: Standard International Group (HK) Limited | Features and Benefits 1.The use of xenon arc lamp as a light source, can simulate the full sunli... |
 |
Single Cable Vertical Flame Tester | 卖方: 上海千实精密仪器 | Introduction Single Cable Vertical Flame Tester is used for the vertical flame propagation of a ... |
 |
Safety Helmet Flammability Tester | 卖方: 上海千实精密仪器 | Product Introduction: Safety hat flame retardant performance tester for safety hat flame retarda... |
 |
Furniture flammability tester | 卖方: 上海千实精密仪器 | Product details Furniture flammability tester is mainly used to test the combustion performance ... |
