Stainless Steel Cylinder Cleaning System
Stainless Steel Industrial Cylinder Cleaning Line (Also Known as Cylinder Cleaning Production Line)
This automated production system specializes in cleaning three-dimensional mixing tanks, mobile cylinders, transfer cylinders, and circulation cylinders. The fully automated process integrates electric-hydraulic controls, high-pressure water jets (20-500 kg/cm²), and multi-axis brush systems to achieve 360° residue removal. Operator supervision is required for process monitoring and auxiliary operations during automated cleaning cycles.
Cleaning Station Configuration
1. Loading Position
2. 180° Flipping Mechanism
3. Internal Scraping & DMF Spraying Station
4. High-Pressure Internal/External Cleaning Module
5. Water Removal & Drying Section
6. Flip Positioning Station
7. Unloading Position
Automated Cleaning Workflow
1. Manual loading into position with open-end facing up (sensor activation)
2. 180° flipping transfer to transition conveyor via hydraulic flipper
3. DMF high-pressure cleaning cycle: Pump station pressurizes solvent (20-500 kg/cm²) → Rotating cleaner enters cylinder → Internal cleaning → Solvent returns to waste liquid collection system
4. Freshwater cleaning phase: Internal high-pressure rinse (35 MPa) + External 360° rotating spray cleaning
5. Drying process: Steam-heated airflow achieves 95% moisture removal rate
6. Intermediate positioning for process synchronization
7. Final 180° unloading flip via pneumatic clamping system
8. Manual consolidation of cleaned cylinders
Key Technical Features
1. DMF solvent recovery system with 92%+ reclamation efficiency
2. Multi-stage filtration (5μm particulate removal)
3. Explosion-proof PLC control cabinet (ATEX Zone 1 certified)
4. Thermal imaging system for temperature monitoring (30-80°C range)
5. Automatic pressure balance with ±0.5 bar tolerance
在线联系供应商
Other supplier products
 |
Glow wire tester | F242 Glow-wire tester, By simulating the thermal stress caused by heat source or ignition source such as hot component or overload resistor in a sh... |
 |
Paper Dirtiness Tester | Introduction: Paper dust meter is suitable for measuring the dust degree of paper or cardboard, books, toilet paper, tissue paper, etc. The dust ... |
 |
Schopper Folding Endurance Tester | Use and Scope of application: 1. the instrument is suitable for tensile strength greater than 1.33kn/m, thickness less than 0.25mm paper folding d... |
 |
Geosynthetic acid and alkali aging tester | Scope of application: Test method for acid-resistant lye properties of various geosynthetic materials; The machine has stirring function, the solu... |
 |
Textile material feel style evaluation instrument | Standards T/CTES 1017-2019 FZ/T 01171-2023 Instrument Features The testing system adopts a biomimetic design, simulating the mechanical tacti... |
Same products
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | 卖方: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | 卖方: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
