Thermal Protective Performance Tester (TPP)

The Thermal Protective Performance (TPP) Test Device was developed to measure the time elapsed for convective and radiant heat to penetrate through a protective composite fabric system - measuring the resulting damage to human skin.

Standards：

BS EN ISO 6942. EN 366. EN 407. ISO 11612. ASTM F1939. ASTM F2702. NFPA 1971. NFPA 2112. GB 38543. GB/T 38306

Feature：

Industrial personal computer with analysis software is suitable for severe testing conditions.

Automatic calculation for heat transmission factor and radiant heat transfer index.

Sample holder with force applied kit is easy to operate.

Single pump for shutter movement and cooling water loop.

Parameter：

• Up to 7.5 in x 7.5 in. (19 cm x19 cm) sample size

• Copper slug calorimeter sensors (ASTM or ISO)

• ± 0.75°C temperature measurement

• ± 3% radiant heat flux measurement

• Device Dimensions: 42 in. x 20 in. x 18 in. (107 cm x 51 cm x 46 cm)

• Space Requirements: 46 in. x 26 in. x 24 in. (117 cm x 67 cm x 61cm)

• Power Requirements: 208-265 VAC, 50/60Hz, Single-phase

• Maximum nominal current 20 Amps

• Compressed Air: Clean/dry air at 70-90 PSI, (145 PSI max)

• Cooling Water: Cooling water required, chiller or tap water source is acceptable

• Propane Requirement: Regulated supply at 15 PSI (minimum)

• Water-cooled radiant heat source with 9 quartz (500W) infrared lamps

• Two gas burners with flame detection auto ignition

• Mass flow controller for precise gas control

• Water-cooled protective shutter

• Pneumatic sample carriage and shutter assembly

• Integrated sensor cooling stand (air cooled)

• Emergency stop cuts gas flow, power to lamps and pneumatics

• Tinted tempered glass shield protects operator

• Software safety interlocks monitor water flow, carriage position, burner ignition

Other supplier products

	High and low temperature memory impact testing machine	Product Introduction: Computer controlled memory impact testing machine is mainly used for hard plastics, reinforced nylon, glass steel, ceramics,...
	Drying Rate Tester	The drying rate tester is a professional device used to measure the drying rate of a substance. Application fields Textile industry: used to eva...
	Ejection Kinetic Energy tester	Product Introduction: Velocity measuring ejection kinetic energy tester, suitable for ejection projectiles, energy storage ejection toys, non-ener...
	Blanket Flammability Test Machine	Introduction Bed Blanket Flammability Tester is used to detect the flame retardant performance of the bed blanket fabric and the flame spread prop...
	Toyota Specialized Abrasion Tester-QINSUN	Standard JIS L 0849(Japanese Industrial Standard for Abrasion Resistance of Textiles) ISO 5470-2(Rubber- or Plastics-Coated Fabrics — Abras...

All supplier products

Same products

	Metal Angular Fixator Testing Machine	Seller: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Metal Angular Fixator Testing Machine...
	Bone Plate Four-Point Bending Fatigue Testing Machine	Seller: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Bone Plate Four-Point Bending Fatigue...
	Bone Plates Static Four - point Bending Tester	Seller: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Bone Plates Static Four-Point Bending...
	Spinal Internal Fixation System Assembly Testing Machine	Seller: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Spinal Internal Fixation System Assem...
	Spinal Internal Fixation System Component Testing Machine	Seller: Standard International Group (HK) Limited	Whats/App: +86 156 1874 6768 Web: standard-groups.com The Spinal Internal Fixation System Compo...