Automotive Windshield Washer Nozzle Fatigue Testing Machine
The Windshield Washer Nozzle Fatigue Test Machine is designed to evaluate the durability and performance of automotive nozzles, including windshield cleaning nozzles (WCS) and headlamp cleaning nozzles (HCS). The machine operates within a controlled environmental chamber, allowing you to simulate temperature and fluid conditions while performing long-term fatigue tests on multiple components simultaneously. Its integrated control and data acquisition system ensures precise monitoring and reliable results.
Standards
The machine complies with international and national automotive testing standards, including:
ISO 6255:1997 – Passenger car windscreen washer systems – Test methods
SAE J942:1999 – Performance requirements and test procedures for passenger car windscreen washing systems
GB 15085‑2013 – Performance requirements and test methods for automotive windshield wipers and washer systems
GB/T 23436‑2009 – Automotive windshield cleaning fluid testing specification
Parameters
| Parameter | Details |
|---|---|
| Test Unit Dimensions | 2030 × 2550 × 1600 mm (W × H × D) |
| Internal Test Unit Dimensions | 1900 × 1150 × 1450 mm (W × H × D) |
| Rated Power | 4 kW |
| Working Fluid | Water – Ethanol mixture |
| Allowable Environment Temperature (Test Unit) | MIN: -25 °C / MAX: 80 °C |
| Number of Test Components | 20 (10 HCS / 10 WCS) |
Accessories
Nitrogen generator for chamber inerting
Fluid supply lines and fittings
Temperature and pressure sensors
Data acquisition modules
Explosion-proof ventilation system
Test Procedures
Install nozzles or components to be tested inside the test chamber.
Connect the working fluid supply (water-ethanol mixture).
Set desired environmental temperature and operational cycles.
Start the test using the PLC-based control unit.
Monitor real-time system parameters including chamber temperature, fluid flow, and nozzle operation.
The machine records all data automatically for later analysis.
After the test, safely remove the components and review recorded fatigue performance.
Maintenance Information
Regularly inspect fluid lines and nozzles to prevent blockage or residue accumulation.
Check nitrogen generator and explosion-proof suction system for proper operation.
Calibrate temperature and pressure sensors periodically for accurate measurements.
Clean the test chamber to remove flammable vapors and fluid residue.
Verify PLC control software and data acquisition integrity before each test cycle.
Send product request
Other supplier products
 |
Wet leakage current test system of photovoltaic module | The Wet Leakage Current Test System is designed for high-precision evaluation of insulation resistance and leakage current in photovoltaic modules ... |
 |
Rubber Mooney Viscosity meter | Test principle: The Mooney viscometer is used to measure the viscosity of rubber under specific conditions. In the test, the rubber sample was loa... |
 |
Contact heat transmission test machine | Introduction: This part of ISO 12127 specifies a test method designed to evaluate the heat transfer and the behaviour ofmaterials used for prote... |
 |
Rapid Closed Cup Flash Point Tester | Reference Standards： SN/T 3077.1、SN/T 3077.2. SH/T 0768. DL/T 1354. ASTM D93、ASTM D6450、ASTM D3828、ASTM D7094、ASTM D7236、ASTM D56、ASTM D56、ASTM... |
 |
Rubber Sleeve Rebound Tester | The Rubber Sleeve Rebound Tester is designed to evaluate the resilience and compression performance of collection needle rubber sleeves. It measure... |
Same products
 |
Automotive seat durability and strength testing machine | Seller: Standard International Group (HK) Limited | The Automotive Seat Three-Station Headrest and Backrest Static Strength Testing Machine is design... |
 |
Racing Seatback Headrest Restraint Device, Front and Rear Impact Testing Machine | Seller: Standard International Group (HK) Limited | The Racing Seat Headrest Restraint and Front-Rear Impact Testing Machine is designed to evaluate ... |
 |
Laboratory car wash simulator for automotive testing | Seller: Standard International Group (HK) Limited | The Laboratory Car Wash Simulator is a specialized testing system designed to replicate automatic... |
 |
Steam jet durability testing machine | Seller: Standard International Group (HK) Limited | The Steam Jet Test Chamber is designed to evaluate the durability and performance of materials an... |
 |
Seat Bumping and Creep Test Bench | Seller: Standard International Group (HK) Limited | Application Applications of the Single Station Jounce Tester include, but are not limited to, th... |
