Flanged Concentric Butterfly Valve
Basic information
This valve offlanged butterfly valve manufacturersis used in various service and drain lines as truncation and regulating equipment.
Features
1. Bidirectional sealing, no flow direction of the medium;
2. Valve body vulcanized EPDM, reliable sealing;
3. A dial with an opening indication showing the position of the disc switch;
4. Flow characteristics straight line, good regulation performance.
2. Valve body vulcanized EPDM, reliable sealing;
3. A dial with an opening indication showing the position of the disc switch;
4. Flow characteristics straight line, good regulation performance.
Principle
The rotary center of the flanged butterfly disc (that is, the center of the stem) is located on the centerline of the valve body and the sealing surface section of the disc. When the disc is closed, the disc's circular sealing surface squeezes the synthetic rubber seat so that the seat produces elastic deformation and forms the elastic force to seal the butterfly valve. If the remote control is required, different types of electric devices can be equipped according to different working conditions.
Installation and Commissioning
Clean the inner cavity and sealing cover of the valve before installation. This butterfly valve can be installed on the horizontal, vertical and any Angle pipe, and can be used in both directions. The butterfly valve must be in the closed position during installation to ensure that the disc does not collide with the pipe flange. Make sure the flange welding is correct. After the butterfly valve is installed, it is not allowed to weld the flange again, so as not to burn the rubber parts and the anti-corrosion coating. For specific use, please consult ZhengFeng Valve Group.
|
Part |
Material |
Standard |
|
Body |
Ductile Iron |
EN 1563/DIN 1693 |
|
Disc |
Ductile Iron |
EN 1563/DIN 1693 |
|
Seat |
EPDM / NBR |
ISO 4633 |
|
Stem |
Stainless Steel 431 |
EN10088-1/ASTM A959 |
|
Bolt |
Stainless Steel 431 |
EN10088-1/ASTM A959 |
|
Worm Actuator |
Ductile Iron |
EN 1563/DIN 1693 |
|
For the materials options not listed, consult factory. ZhengFeng manufactures valves in more than 50 different alloys. |
||
Send product request
Other supplier products
 |
Flange Globe Valve | Category: Globe Valve Description Globe stop valveprovide superior performance and reliability in a wide range of applications. What is a Fl... |
 |
3 Inch Gate Valve | Description of 3 Inch Gate Valve: ZECO 3 inch stainless steel gate valveand 2 flanged gate valveis mainly used for fully open or fully closed swit... |
 |
4 Inch Gate Valve | Description of 4 Inch Gate Valve: ZECO 4 flanged gate valveis one of the most commonly used calibers. Gate valve in the line just switch effect, lo... |
 |
Flapper Check Valve | Basic informationThis can be installed at the water outlet of the pump or the water outlet pipe to prevent backflow of the medium.Features1. Switch... |
 |
Resilient Gate Valve for Underground 1025 | Basic information This underground gate valveis used as a two-way closed circuit device. Featuresof Resilient Gate Valve for Underground Principleo... |
Same products
 |
Class 300 Valve | Seller: GangYe Group Co.,Ltd. | Class 300 valves have a pressure rating of 300 pounds per square inch (psi) or 20.7 bar, allowing... |
 |
Class 3000 Industrial Valve | Seller: GangYe Group Co.,Ltd. | Wafer Body, Full Port Design, Flanged End Class 3000 Ball Valve. A ball valve class 3000pressure-... |
 |
Class 2500 Industrial Valve | Seller: GangYe Group Co.,Ltd. | Class 2500 valves can be used for both on-off and throttling applications. The specific valve typ... |
 |
Class 150 Valve | Seller: GangYe Group Co.,Ltd. | globe valve class 150is a pressure rating designation defined by standards organizations, such as... |
 |
Class 1500 Industrial Valve | Seller: GangYe Group Co.,Ltd. | A class 1500 valve made of 316 stainless steel, for instance, can sustain 248 bar of pressure at ... |
