new UHP grade electrode Petroleum coke

• 
• 
• 

DESCRIPTION

UHP graphite electrode is used for the recycling of steel in the electric arc furnace industry. Its main ingredient is high-value needle coke which is made from either petroleum or coal tar. Graphite electrodes are finished with a cylinder shape and machined with threaded areas at each end. In this way, the graphite electrodes can be assembled into an electrode column using electrode nipple.

In order to meet the requirement of higher work efficiency and lower total cost, large capacity ultra-high power arc furnaces are becoming more and more popular. Because of this, UHP graphite electrodes with diameters of over 500 mm will dominate market.

FEATURE

Withstand large currents, high discharge rate.Good dimension stability, not easy to deform.Resistant to cracking & spalling.High resistance to oxidation and thermal shock.High mechanical strength, low electrical resistance.High machining accuracy, good surface finishing.

APPLICATION

Graphite electrodes are widely used for production of alloy steels, metal and other nonmetallic materials, etc.DC electric arc furnace.AC electric arc furnace.Submerged arc furnace.Ladle furnace.

SPECIFICATION

Table 1: Technical Specification of UHP Graphite Electrode

Table 2: Graphite Electrode Size & Tolerance

SURFACE QUALITY

There should be less than two defects or holes on the electrode surface, the maximum size of which is mentioned in the below chart.There should be no transverse crack on the electrode surface. For the longitudinal crack, the length should be less than 5% of the electrode circumference and the width should be 0.3 to 1.0 mm.The width of black area on electrode surface should be less than 1/10 of the electrode circumference and the length should be less than 1/3 of the electrode.

Guidance of UsingBeing hard and brittle ,artificialgraphite electrode shall be specially handled.Proper operationg may reduce the consumption and cost.1. Professional tools should be used for hoisting graphite electrodes. It is strictly forbidden to use a crowbar to prevent impact damage during handling.2.Graphite electrodes are prohibited from rain, snow and water, and should be kept dry. If it is found to be damp, it should be dried before use, the temperature should not exceed 100 ºC, and the drying time should not be less than 48h.3.Do not stack near debris such as clay, slag, etc., so as not to pollute the surface of the graphite electrode and affect the conductive effect.4.Before the graphite electrode is connected, carefully check whether the electrode connector hole is intact, whether the connector thread is damaged, and whether the connector bolt is lost. When the electrode is lifted, the electrode connector thread of the ground terminal should be prevented from being damaged.5.Dust and debris in the joints and joint holes should be blown dry with compressed air.6.Graphite electrodes must be tightly connected, and no tilt is allowed during connection. Torque wrenches should be used to prevent excessive force or too small, and the gap is not greater than 0.4mm.7.The electrode holder should be clamped, not loose and in good contact, and no arc should be generated. Otherwise, the connection will be reddish, oxidized, thinned and broken.8.If the electrode is lifted with a metal lifting plug, the thread in the joint hole must not be damaged. After lifting, the lifting plug should be unscrewed to prevent dust and debris from falling into the joint hole.9.When the electrode lifting device of the electric furnace is running, it should be kept stable. After the furnace cover is repaired, check whether the furnace cover is positioned correctly. During smelting, refractory materials are used to close the furnace lid to prevent the oxidation of the upper electrode of the flame in the furnace.10.The holder should be clamped outside the safety wire of the electrode connector hole area.11.When distributing the molten pool, the big piece is at the bottom and the small piece is at the top. Do not place the charge with poor conductivity on the top. During melting, the unmelted charge should be handled in time to prevent the collapsed material from breaking the electrode.

Other supplier products

	UHP graphite electrodes	DESCRIPTION UHP graphite electrode is used for the recycling of steel in the electric arc furnace industry. Its main ingredient is high-value need...
	new UHP grade electrode Petroleum coke	DESCRIPTION UHP graphite electrode is used for the recycling of steel in the electric arc furnace industry. Its main ingredient is high-value need...
	Various specifications of graphite electrodes	We are a graphite electrode factory, if you want to purchase more details, please contact
	Professional Supply Low Sulphur CPC GPC Graphitized/Calcined Petroleum Coke	DESCRIPTION UHP graphite electrode is used for the recycling of steel in the electric arc furnace industry. Its main ingredient is high-value need...
	High quality high and low power graphite electrodes	DESCRIPTION UHP graphite electrode is used for the recycling of steel in the electric arc furnace industry. Its main ingredient is high-value need...

Same products

	Ultra-high power graphite electrode	Seller: Handan Hongguan New Material Technology Co., Ltd.	Ultra-high power graphite electrodes are mainly used for the electrode parts in high-temperatur...
	Chongqing Firefly New Materials TechnologyCo.. Ltd.	Seller: 833804	Research and development, production, and sales of graphite materials and products; Research and ...
	Chongqing Firefly New Materials TechnologyCo.. Ltd.	Seller: 833804	Research and development, production, and sales of graphite materials and products; Research and ...
	CUSTOM EXTRUDED GRAPHITE BLOCK	Seller: Pingdingshan Wanhui Graphite Co., LTD	Extruded graphite block, mainly used for molten iron with casting molds and graphite crucible fur...
	CUSTOM GRAPHITE EDM BLOCKS	Seller: Pingdingshan Wanhui Graphite Co., LTD	EDM graphite blocksare becoming more and more popular among our customers. EDM graphite is a new ...