Sand - Falling Testing Machine for Motorcycle Helmets
Main Purposes
It is mainly used to test the abrasion - resistance of the lenses of helmet goggles and evaluate their ability to resist particle - induced damage.
Applicable Standard
ASTM D968-83
JG/T 133-2000
Instructions for use:
1. according to the standard requirements for the preparation of test plates and placed in (23 +-2) degrees Celsius, relative humidity (50 +-5) degrees Celsius conditions for 24 hours.
2. Calibrate the apparatus:
Pour a certain amount of sand into the funnel, check the sand stream falling from the lower end of the conduit, and calibrate the device with the bottom adjusting screw until the inner part of the sand beam falls exactly on the center of the sand stream when viewed from two positions of 90 degrees Celsius each other. Use the high and low adjusting nut to adjust the distance from the tube tube to the painted surface according to the ASTM standard, when measured in the vertical direction, the near point of 1 inch (25mm), the user needs to be adjusted according to the thickness of their own samples, factory machine pre-adjustment of 25mm. to the pouring of a certain volume amount of sand (to 2000 +-10ml is appropriate), and measure the outflow time, the outflow rate should be 21S- 23.5S within 2L. This speed comes from the ASTM standard, and with the international standard sand for the test, we measured the speed of 1 minute 7L or more.
3. do the test should pay attention to, after the end of the sand fall, the machine should be slightly tilted to make the lower funnel in the small square of excess sand poured out, in the re-insertion of the sand fall switch in order to avoid the sand fall switch can not be put in.
Main Technical Parameters:
Overall Dimension: 230mm×200mm×1500mm (L×W×H)
Catheter Length: 36 inches (914mm)
Catheter I.D.: 0.75 inches (19mm)
Hopper Volume: 3L
Machine Weight: 25KG
Send product request
Other supplier products
 |
Sweating Thermal Manikin/ Thermal Comfort Testing Manikin / Heat and Sweat Simulation Manikin | Introduction The sweating thermal manikin test system simulates the physical mechanism and heat exchange from the outside world. Obtain the thermal... |
 |
Button Impact Machine | Testing Standards: ASTM D5171 Application:Button falling weight impact testeris used to determine the impact resistance of plastic sew-through fl... |
 |
Paper stiffness meter | Paper stiffness meter - Other test instrument - standard Product Introduction: ZY-TDY300 microcomputer bending stiffness tester is used to measur... |
 |
Gas Oxidizing Property Tester | Product Information: 1. The test device and the control system adopt a split - structure design to ensure the safety of the instrument control uni... |
 |
Footwear Dynamic Waterproof Tester | Product Introduction: It is used to test the dynamic waterproof performance of various finished shoes, and the number of times when no water enter... |
Same products
 |
KL‑016A Benchtop High‑precision pH Meter | Seller: Kelilong Electron Co.Ltd | Product Description: Large‑screen display with high resolution and precision for con... |
 |
Large Naïve VHH Library | Seller: AlpVHHs | Large Naïve VHH Library VHHare single-domain antibodies derived from the variable regions o... |
 |
pH-2398 pH/EC/ORP/Temperature multi-parameter Water Quality Tester | Seller: Kelilong Electron Co.,Ltd | Feature Large display screen, capable of simultaneously measuring water quality pH, redox potent... |
 |
ORP-2026S Waterproof Soil ORP and Temperature Meter | Seller: Kelilong Electron Co.,Ltd | 范围 ORP -999～999mV Temp 0～50℃ 分辨率 ORP 1mV... |
 |
TDS-2616 Waterproof EC/TDS/Temperature Meter | Seller: Kelilong Electron Co.,Ltd | Range EC ～19.9mS TDS Temp 0～50℃ R... |
