PTAW Welding
PTAW Welding
WALKSON can provide specially formulated Tungsten Carbide Overlay (TCO) applied by Plasma Transferred Arc Welding (PTAW) process on any casting or fabrication part surface to increase the wear-resistant property of the part.
For extremely abrasive applications, the overlay properties in the following chart will be used. The lifecycle of this type of overlay by PATW welding is 5-6 times longer than Chrome Carbide Overlay. Typical Applications of this kind of overlay are Slurry line, slurry pump suction and discharge spool, wear spool, spray nozzles.
Why Choose WALKSON PTAW Welding
For heavy load applications, the tungsten carbide is 60-70 wt % and the balance is NiB matrix. The particle size of prime carbide is in the range of 60-325 mesh (44-250 micron) with hardness HV 2700-2900. The bulk hardness of NiB matrix is HRC 45-55.
This formula is designed for medium to heavy load application. The combination of high hardness of the prime carbide and high toughness of the matrix make the wear products excellent for high-impact applications. Its lifecycle is 5-6 times longer than AR plates.
Applications of PTAW Welding
Typical Applications of this kind overlay is Rotary screen wear plates, shovel teeth, crusher teeth and liner plates, grinder hammer tips, chutes/hoppers and mining picks.
Wear Protection Products-PTAW/Plasma Transferred Arc Welding Machine
WALKSON can provide specially formulated Tungsten Carbide Overlay (TCO) applied by Plasma Transferred Arc Welding (PTAW) process on any casting or fabrication part surface to increase the wear resistant property of the part.
For extremely abrasive applications, the overlay properties in the following chart will be used. The lifecycle of this type overlay by PATW is 5-6 times longer than Chrome Carbide Overlay.
Typical Applications of this kind overlay is Slurry line, slurry pump suction and discharge spool, wear spool, hammer tips, spray nozzles.
|
Overlay Properties |
WC |
Matrix |
|
Composition (wt%) |
70 -75 % |
Balance |
|
Hardness |
2700- 2900 HV |
60-70 HRC |
|
Particle size (micron) |
44 - 250 |
53-198 |
|
Overlay Thickness (mm) |
3 - 15 mm |
|
|
Bulk Hardness |
832 -1076 HV / 65-70 HRC |
|
For heavy load applications, the tungsten carbide is 60-70 wt % and the balance is NiB matrix. The particle size of prime carbide is in the range of 60-325 mesh (44-250 micron) with hardness HV 2700-2900. The bulk hardness of NiB matrix is HRC 45-55.
This formula is designed for medium to heavy load application. The combination of high hardness of the prime carbide and high toughness of the matrix make the wear products excellent for high-impact applications. Its lifecycle is 5-6 times longer than AR plates
Typical Applications of this kind overlay is Rotary screen wear plates, shovel teeth, dragline teeth, crusher teeth and liner plates, grinder hammer tips, chutes/hoppers and mining picks.
|
Overlay Properties |
WC |
Matrix |
|
Composition (wt%) |
60 -70 % |
Balance |
|
Hardness |
2300- 2600 HV |
45-55 HRC |
|
Particle size (micron) |
44 - 250 |
53-198 |
|
Overlay Thickness (mm) |
3 - 15 mm |
|
|
Bulk Hardness |
720-865 HV / 61-66 HRC |
|
WALKSON had been create milestone in the year 2021, we successfully applied PTAW Tungsten Carbide Overlay (TCO) on the valve sealing area with 8mm-12mm use stellite 6 cobalt base, this is the first successful trial with such thickness in china, WALKSON become the first company which can applied PTAW Tungsten Carbide Overlay (TCO) for the valve sealing field.
What is Plasma Transferred Arc Welding Process?
PTA stands for plasma transferred arc welding, which is a natural progression of the GTAW method. It's a simple-to-automate connection approach that produces higher-quality joins and welds by precisely controlling critical welding parameters. It's perfect for surfacing and cladding in heavy sectors including oil and gas, mining, and energy generation. Plasma transfer arc welding is a time-consuming and difficult joining method. It works by inducing a high-density plasma transfer arc, which has enough energy to melt the base metal workpiece and metal filler powder. The pilot arc is first created by ionizing inert gases (argon, helium, hydrogen, etc.) with the tungsten electrode and torch nozzle arc. By discharging plasma gas through the decreasing nozzle, the pilot arc is turned into a transfer arc. The plasma column is essentially throttled to a high temperature, a high jet velocity, and a high energy density.
References of PTA Process
[1] Plasma transferred arc welding—modeling and experimental optimization. [J] J. Wilden, J. P. Bergmann & H. Frank. December 2006.
[2] Microstructure and wear properties of nickel-based surfacing deposited by plasma transferred arc welding. [J] Chen Guoqing, Fu Xuesong, Wei Yanhui, Li Shan, Zhou Wenlong. 15 August 2013, Pages S276-S282.
Transferred VS. Non-transferred Plasma Arc Welding
The main arc in TPAW is established between the tungsten electrode and the guide electrode. Compared with non-transferred plasma arc welding (NPAW) where one of the arc terminals is a nozzle, the workpiece is not connected to the circuit, and the energy loss is less than NPAW.
As the welding current and plasma gas flow rate increase, the diameter of the ablation zone of the TPAW (ie, the energy received by the workpiece) is much larger than the diameter of the NPAW. The MZ area and HAZ area of the TPAW weld are smaller, but the penetration depth of the PAW weld is similar.
Under the same parameters, the MZ or HAZ cannot be observed in the NPAW weld, indicating that the total heat input distribution of TPAW is much larger than that of NPAW . This trend provides a possible way to better control the energy of the plasma arc and expand the application of the plasma arc.
We can also offer kinds of shovel replacement partsfor sale, if you have needs, please contact us.
Send product request
Other supplier products
 |
CrMo Alloy Liners | WALKSONcan provide a wide range of wear resistant products for mineral processing industry. The role of a CrMo mill lineris to give the mill heads ... |
 |
CNC Machining | At present, our machining shop, providing production cnc machining, as well as cnc machining and manufacturing services, has more than 50 kinds of ... |
 |
Safety Valve | WALKSON, as a professional pressure safety valve manufacturers, supplies main parts for pressure safety valve, consisting of Valve Body, Disc, Stem... |
 |
White Iron Liners | We can provide a wide range of wear resistant products for mineral processing industry. The role of a white iron mill lineris to give the mill head... |
 |
Heat Treatment | Our heat treatment facility covers an area of 33300 square meters with more than 50 million RMB fixed assets. The annual output of heat treatment i... |
Same products
|
|
PTAW Welding | Seller: Yiwu WALKSON Machinery Equipment Co., Ltd. | PTAW Welding WALKSON can provide specially formulated Tungsten Carbide Overlay (TCO) applied by ... |
 |
White Iron Liners | Seller: Yiwu WALKSON Machinery Equipment Co., Ltd. | White Iron Liners We can provide a wide range of wear resistant products for mineral processing ... |
 |
Shroud | Seller: Yiwu WALKSON Machinery Equipment Co., Ltd. | Shroud Cast shrouds are casings used on bucket lip to protect your bucket lip from aggressive we... |
 |
Rigging Components | Seller: Yiwu WALKSON Machinery Equipment Co., Ltd. | Rigging Components WALKSON manufacture most parts of the dragline riggingand structural componen... |
 |
Ni-hard Wear Liners/ Billets | Seller: Yiwu WALKSON Machinery Equipment Co., Ltd. | Ni Hard Liners/ Billets NiHard is a well-established white iron product alloyed with nickel and ... |
