F-1B Kraft Tape Dispenser

Produced by: KUNSHAN BOJIN TRADING CO.,LTD.

All supplier products

Operation Video ofF-1B Kraft Tape Dispenser

Before using this machine carefully read the operating instructions. They contain important indications on installation safety, use and maintenance.
Keep this manual with care for any further reference.
It's customer's responsibility to make sure that the personnel who will use the machines read and understand the manual.
The builder cannot be responsible for eventual damage to people deriving from non deservation of the safety norms and the warnings here contained.

This tape dispenser is designed and manufactured only to dispense gummed tape, any different use from that advised is not considered specific. PRINCE PACKAGING will not assume any responsibility following an improper use of the machine.
After unpacking, check the integrity of the machine, in case of doubt does not use the machine and enquire directly to the reseller.
Keep the machine away from children and from personnel who are not authorized or adequated in the use of it.
Follow the instruction manual for machine maintenance.

Before using a new dispenser, wash the moistening brush with cleanser, and rinse it with water.
Insert the brush in the water tank.
Place the lever straight up with your right hand.
Take the water tank with the left hand to the groove in the front of the machine until it touches the back part of the machine.
Lower the water tank till it locks into position.
Let go hold of the feed-in control haulm.

Fill the water through the hole with clean water.
Put a finger on the hole, place the bottle back in its housing, the water will pour from the bottle to the tank.

Adjust the moistening of the tape according to the quality of glue and paper. Increase or decrease the water quantity in the tank, and therefore on paper, raise or lower the lever by placing the water bottle in one of the three different positions in the water tank.(minimal, medium and maximum lever)

Insert the moving plate with the bent part facing up in its housing placed under the white wheel, pushing it ahead.

Rolls of gummed paper can be rolled in two different ways:
With glue facing out the roller should be placed in position A. With glue facing in the roller should be placed in position B.

Adjust roll guide plates to the width of tape and place in their seats. Insert the tape in the guide plates so that the paper comes with the gummed side down, then insert the gummed tape under the moving plate, pushing it all the way. Make sure that the moving plate presser on the tape.

Before removing the bottle, make sure that it doesn't contain water, otherwise cover the filling hole with the finger to avoid outlet of water. Filling the bottle and place it bac in its housing.
AFTER HAVING FOLLOWED THE ABOVED INSTRUCTIONS, THE MACHINE IS READY.
Our machines are safe, repairs have to be made in our assistance centers or by specialized personnel, improper repairs could cause accidents to the user.

	BJ-08T Wire Twisting Machine	Product features ofWire Twisting Machine BJ-08T Axis design, while standing! Greatly improve production efficiency LCD backlit display, modern ...
	Automatic Tape Dispenser	M-1000 Automatic tape dispenser * Tape Width: 7 ~ 50mm* Cut Length: 5 ~ 999mm, Digital Length Adjustment.* Length setting: Digital* Ac...
	Round Bottle Labeling Machine	Common Problems of Semi—AutomaticRound Bottle Labeling Machine Ⅰ. The position of labeling is unstable 1. It is likely that the pressure ...
	Label Cutting Machine	Description ofLabel Cutting Machine With Cold & Hot Cutting BJ-07N Model: BJ-07N with Memory Knife: Hot & Cold cutting CUT LENGTH (mm)...
	Coaxial Wire Stripping Machine	Operating procedures of semi-automaticcoaxial wire stripping machine. 1. PurposeEstablish proper equipment to prevent accidents and ensure the nor...

The Ultimate Tool for Bubble-Free Displays	Seller: Shenzhen Wikshu Technology Co.	FORWARD FW-16R Bubble Remover and FW-8R Mini Bubble Removal Machine removes screen OCA bubbles du...
Precision CNC Lathe With Conjoined Oblique Rail Cutter Tower	Seller: Zhejiang Guoyu CNC Machine Tool Co., Ltd.	Technical Characteristics: 45° slant bed base structure, with strict aging treatment, smooth ...
Rail Welder A Frame aligners railway welding tools	Seller: 834406	产品描述 A型车架 A-Frame 是一种导轨对准器，可精确对准要焊接的导轨。该设备在焊接操作期间将导轨固定到位。
2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	Seller: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
Horizontal Machining Center	Seller: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...