F-1B Kraft Tape Dispenser

Operation Video ofF-1B Kraft Tape Dispenser

Specifications ofF-1B Kraft Tape Dispenser

• Size: 380*300*250mm
• Weight: 9.0kg
• Available width: 15-110mm, length: 50-1100mm
• Water Brushes: 2 for consistent, uniform tape wetting
• Water Bottle Capacity: 41 ounces (1.2 liters)
• Electrical Requirements: None (optional Top Heater requires electrical power)
• Warranty: 2 year parts, 6 months labor

Attention ofF-1B Kraft Tape Dispenser

• Before using this machine carefully read the operating instructions. They contain important indications on installation safety, use and maintenance.
• Keep this manual with care for any further reference.
• It's customer's responsibility to make sure that the personnel who will use the machines read and understand the manual.
• The builder cannot be responsible for eventual damage to people deriving from non deservation of the safety norms and the warnings here contained.

General Remarks

ofF-1B Kraft Tape Dispenser

• This tape dispenser is designed and manufactured only to dispense gummed tape, any different use from that advised is not considered specific. PRINCE PACKAGING will not assume any responsibility following an improper use of the machine.
• After unpacking, check the integrity of the machine, in case of doubt does not use the machine and enquire directly to the reseller.
• Keep the machine away from children and from personnel who are not authorized or adequated in the use of it.
• Follow the instruction manual for machine maintenance.

Mounting the water tank

ofF-1B

• Before using a new dispenser, wash the moistening brush with cleanser, and rinse it with water.
• Insert the brush in the water tank.
• Place the lever straight up with your right hand.
• Take the water tank with the left hand to the groove in the front of the machine until it touches the back part of the machine.
• Lower the water tank till it locks into position.
• Let go hold of the feed-in control haulm.

Filling the water bottle ofF-1B Kraft Tape Dispenser

• Fill the water through the hole with clean water.
• Put a finger on the hole, place the bottle back in its housing, the water will pour from the bottle to the tank.

Contral of moistening level ofF-1B Kraft Tape Dispenser

• Adjust the moistening of the tape according to the quality of glue and paper. Increase or decrease the water quantity in the tank, and therefore on paper, raise or lower the lever by placing the water bottle in one of the three different positions in the water tank.(minimal, medium and maximum lever)

Placing the moving plate ofF-1B Kraft Tape Dispenser

• Insert the moving plate with the bent part facing up in its housing placed under the white wheel, pushing it ahead.

Inserting roller ofF-1B Kraft Tape Dispenser

• Rolls of gummed paper can be rolled in two different ways:
• With glue facing out the roller should be placed in position A. With glue facing in the roller should be placed in position B.

Loading of tape roll ofF-1B Kraft Tape Dispenser

• Adjust roll guide plates to the width of tape and place in their seats. Insert the tape in the guide plates so that the paper comes with the gummed side down, then insert the gummed tape under the moving plate, pushing it all the way. Make sure that the moving plate presser on the tape.

Removing and filling the bottle ofF-1B Kraft Tape Dispenser

• Before removing the bottle, make sure that it doesn't contain water, otherwise cover the filling hole with the finger to avoid outlet of water. Filling the bottle and place it bac in its housing.
• AFTER HAVING FOLLOWED THE ABOVED INSTRUCTIONS, THE MACHINE IS READY.
• Our machines are safe, repairs have to be made in our assistance centers or by specialized personnel, improper repairs could cause accidents to the user.

Related Automatic Tape Dispensers

Brand	Model	Cutting length	Cutting width
BOJIN	M-1000	5-999mm	7-50mm
BOJIN	BJ-2000S	5-999mm	5-50mm
BOJIN	M-1000S	5-999mm	5-50mm
BOJIN	ZCUT-2	13-60mm	3-25mm
BOJIN	RT-3000	9-61mm	3-25mm
ELM	M-1000	20-999mm	7-50mm
ELM	MS-1100	30-999mm	7-50mm
ELM	TDA-080	40-999mm	13-80mm
YAESU	ZCUT-7	5-999mm	6-50mm
YAESU	ZCUT-9GR	5-999mm	6-60mm
YAESU	ZCUT-870	15-70mm	3-25mm
YAESU	ZCUT-9	5-999mm	6-60mm
YAESU	ZCUT-9P	5-999mm	6-60mm
ASUTECH	ED-100	5-999mm	7-50mm

Другие товары поставщика

	Labelcombi-100 Label Sticker Dispenser	Features ofLabelcombi-100 Label Sticker Dispenser The smallest area occupation, becomes to everywhere with its pretty and class design for stick...
	Label Cutting Machine	Label Cutting Machine Label Cutting Machine With Cold & Hot Cutting BJ-07N * Knife: Hot & Cold cutting* CUT LENGTH (mm): 1-99...
	Coaxial Wire Stripping Machine	Operating procedures of semi-automaticcoaxial wire stripping machine. 1. PurposeEstablish proper equipment to prevent accidents and ensure the nor...
	Automatic Tape Dispenser	The working principle of tape dispenser： The tape dispenser is also called a belt cutter. It is mainly used to cut the tape up and down the blade,...
	Enameled Wire Stripping Machine	Installation and use of . Choose appropriate peeling wheel and install them on the machine. Put two enameled wire in the middle of the peeling whe...

Все товары поставщика

Похожие товары

	2 parts fluid mixing dispenser 2 component dosing epoxy PU silicon rubber vacuum system	Продавец: 824681	What is the difference between 2K AB adhesive materials manual potting machine and robot pottingm...
	Horizontal Machining Center	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	Horizontal Machining Center parts can automatically finish four sides milling, boring, drilling, ...
	Horizontal Lathe	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	As a professional horizontal lathe manufacturerand horizontal lathe factory, Sealion Machine Tool...
	Gantry Machining Center	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	SEALION supplies Gantry Machining Center both tables moving type or gantry moving type. Gantry ty...
	Floor Type Boring Mill	Продавец: Xilong (Shanghai) Machine Tool Co., Ltd.	Floor Type Boring Mill is suitable for large size jobs to do milling, boring, drilling, etc. The ...