Windshield Wiper Blades
Because of legal requirements, almost everywhere cars must be equipped with windshield wiper cutter. The windshield wiper cutter also has the characteristics of heat resistance, cold resistance, acid and alkali resistance, corrosion resistance, can fit the windshield, reducing the burden on the motor, low noise, strong water repellency, soft and does not scratch the windshield. We manufacture three types of rain wiper blades, conventional wiper blades, flat windshield wiper blades and hybrid wiper blades.
Windshield wiper cutters are consumables, and their lifespan also depends on the road conditions, environment, temperature, etc. Generally, rain wiper blade cutters are replaced in about a year, mainly depending on the frequency of use. The car owner can also clean the rain wiper blade cutter with a towel after it rains, which not only increases the service life but also protects the glass. Whether the rain wiper blade cutter can work normally or not directly affects the safety and comfort of driving, it is recommended to check and replace it regularly. For bulk conventional wiper blades, flat windshield wiper blades and hybrid wiper blades direct from MAPMS at competitive prices.
What Are the Symptoms of a Bad Windshield Wiper Blade Cutter？
The scraping is not clean and there is abnormal sound
It means that the rain wiper blade cutter arm is twisted upward. Make the wiper is stopped in the middle position and pull the wiper switch handle towards the steering wheel after the car is turned off, and then gently lift it. Wrap the rain wiper blade cutter arm with a cloth or something soft, use a wrench or pliers to clamp the wrapped part down and twist it a few times. After resetting automotive wiper system, try scratching it. The abnormal noise will be much smaller. If it is, repeat it until the abnormal noise is eliminated. If the rain wiper blade cutter arm is in the down position, it needs to be twisted in the opposite direction until the abnormal noise is eliminated.
The wiper blade
The rain wiper blade cutter is a rubber product, and it will age and harden after using it for a period of time, especially in winter Generally, wiper blades are recommended to be replaced every one to two years.
The wiper blade clean
There are articals between the wiper blade box and the windshield. When the rain wiper blade cutter is turned on, there will be a sharp sound of friction between the rain wiper blade cutter and the front windshield. In this case, you can check and clean up the articals under the wiper blade or wiper arm to keep the wiper blade clean.
Abnormal Noise
The deformation of the linkage mechanism or the influence of the motor and the gap relay, such as too fast or too slow or non-stop action, may cause abnormal noise, and due to wear, the card issuance, rust of its own mechanism, also cause to behave abnormally and so on. If it is a new rain wiper blade cutter, it is recommended to check whether there is dirt or oil stains on the windshield. It is recommended to clean the windshield with cleaning fluid or try a new one. If there is still abnormal noise, use a tool such as pliers to adjust the angle of the rain wiper blade cutter arm. However, it is recommended to go to the repair shop for special tools to adjust.
The most of common case
There is a rattling sound when the wiper wipes the windshield wiper cutter. The wrong windshield wiper cutter arm angle is the most of common case, which causes the wiper blade to jump on the windshield, resulting in abnormal noise. If the windshield wiper cutter is normal, then the angle of the wiper arm needs to be adjusted, and the wiper blade should be perpendicular to the windshield plane. Put a rag on the head of the wiper arm, then clamp it with pliers, and break it hard correctly, try to make the wiper blade perpendicular to the windshield plane.
For more car auto spare partswholesale at competitive price directly from China factory.
Send product request
Other supplier products
 |
Fuel Pressure Sensors | The fuel vapor vent pressure sensoris used to control the fuel pressure in the fuel circuit, maintain a constant fuel supply pressure to the inject... |
 |
Airbag Sensor | The airbag sensor is the input device of control signal in the SRS system. When the vehicle happens to collides, the airbag sensor detects the inte... |
 |
Headlight Bulbs | HID Car Headlight Bulbs also named Xenon Bulbs High Brightness. 35W xenon lamp can produce 3200 lumens of bright light. Wide color temperature ra... |
 |
Radiator Pressure Caps | When the car is running, the temperature of the coolant rises and the pressure in the radiator increases. When the pressure reaches a certain level... |
 |
Cabin Filters Application | automotive parts industry/ automobile parts manufacturing industry/ industry auto parts The cabin filter filters the air in the car compartmen... |
Same products
 |
Windshield Wiper System | Seller: Guangzhou May Import & Export Trading Co.,Ltd | The system is not only as simple as wiping the water off the windshield, but also wipes the rainw... |
|
|
Windshield Wiper Blades | Seller: Guangzhou May Import & Export Trading Co.,Ltd | Because of legal requirements, almost everywhere cars must be equipped with windshield wiper cutt... |
 |
Turn Signal Switches | Seller: Guangzhou May Import & Export Trading Co.,Ltd | The clockwise lever of the aftermarket signal light switchturns right, the counterclockwise lever... |
 |
Trumpet Horns | Seller: Guangzhou May Import & Export Trading Co.,Ltd | The trumpet electric horn continuously vibrates through the diaphragm, thereby emitting sound wav... |
 |
Pencil Ignition Coils | Seller: Guangzhou May Import & Export Trading Co.,Ltd | The Pencil Type Ignition Coil combines the high-voltage ignition wire and the ignition coil into ... |
